Difficulty
Moderate
Steps
12
Time Required
30 minutes
Sections
1
- Moen Posi-Temp Cartridge Part #1112b
- 12 steps
Flags
0
BackPlumbing
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
Before replacing the cartridge, first check a nearby faucet or shower to see if it is also getting inconsistent water temperature. If it is not, then the problem would be the valve’s cartridge and would need to be replaced.
This guide will take you through the steps of replacing the cartridge of a Moen Posi-Temp shower valve.
This procedure will take you through the plumbing so make sure that you locate the main shutoff valve to the shower or to the house as you would need to turn off the water for this procedure.
What you need
Step 1
Moen Posi-Temp Cartridge Part #1112b
- Turn the water shutoff valve counter-clockwise to the “off” position.
Turn the water shutoff valve counter-clockwise to the “off” position.
1024
Step 2
- Open both the hot and cold taps of a nearby faucet or shower until the water no longer flows.
Open both the hot and cold taps of a nearby faucet or shower until the water no longer flows.
Step 3
- Turn the handle of the shower valve 180 degrees until it is in the “up” or “on” position.
Turn the handle of the shower valve 180 degrees until it is in the “up” or “on” position.
Step 4
- Unscrew the handle screw with an Allen wrench.
- Remove the handle.
Unscrew the handle screw with an Allen wrench.
Remove the handle.
Step 5
- Remove the handle adaptor screw with a Phillips screwdriver.
- Remove the handle adaptor simply by pulling it out.
Remove the handle adaptor screw with a Phillips screwdriver.
Remove the handle adaptor simply by pulling it out.
Step 6
- Pull out the white key/adjustable limit stop.
Pull out the white key/adjustable limit stop.
Step 7
- Gently pull out the stop tube.
Gently pull out the stop tube.
Step 8
- Using the Phillips head screwdriver, remove the two screws located at the top right corner and bottom left corner.
- Remove the metal plate.
Using the Phillips head screwdriver, remove the two screws located at the top right corner and bottom left corner.
Remove the metal plate.
Step 9
- Slide the tip of needle-nose pliers under the notch of the retaining clip and pull the clip upwards.
Slide the tip of needle-nose pliers under the notch of the retaining clip and pull the clip upwards.
Step 10
- Clamp firmly onto the brass tube with a pair of vice grips and gently but firmly pull out the cartridge.
Clamp firmly onto the brass tube with a pair of vice grips and gently but firmly pull out the cartridge.
Step 11
- Insert the new Moen Posi-Temp cartridge.
Insert the new Moen Posi-Temp cartridge.
Step 12
- Insert the new cartridge into the valve assembly.
- Ensure that the H/C symbols are facing up.
- Ensure that the notch on the brass tube is also facing up.
Insert the new cartridge into the valve assembly.
Ensure that the H/C symbols are facing up.
Ensure that the notch on the brass tube is also facing up.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 1 other contributor
John Mendoza
Member since: 09/17/2020
205 Reputation
1 Guide authored
Badges:
3
Team
York University, Team S3-G57, Melo-Thaiss Fall 2020
Member of York University, Team S3-G57, Melo-Thaiss Fall 2020
YORK-MELO-THAISS-F20S3G57
1 Member
1 Guide authored