Difficulty
Moderate
Steps
14
Time Required
30 - 45 minutes
Sections
3
- Housing Assembly
- 2 steps
- Reduction Gear Assembly
- 10 steps
- Diaphragm Assembly with Bushing
- 2 steps
Flags
2
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
BackMilwaukee 5262-21
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Housing Assembly
- Remove the ten 19mm T20 Torx screws shown in red.
Remove the ten 19mm T20 Torx screws shown in red.
1024
Step 2
- Remove the red Housing Assembly by lifting it up off of the tool.
Remove the red Housing Assembly by lifting it up off of the tool.
Step 3
Reduction Gear Assembly
- Remove the two 10mm T-10 Torx screws that attach the top brush holders to the motor housing.
- Remove the two 10mm T-10 Torx screws that attach the bottom brush holders to the motor housing.
Remove the two 10mm T-10 Torx screws that attach the top brush holders to the motor housing.
Remove the two 10mm T-10 Torx screws that attach the bottom brush holders to the motor housing.
Step 4
- Using a metal spudger, pry off each brush holder.
Using a metal spudger, pry off each brush holder.
Step 5
- Remove the four 37mm T20 Torx screws shown in red.
Remove the four 37mm T20 Torx screws shown in red.
Step 6
- Pull the front portion of the tool out from the motor housing.
Pull the front portion of the tool out from the motor housing.
Step 7
- Remove the two 11.5mm T10 Torx screws shown in red.
Remove the two 11.5mm T10 Torx screws shown in red.
Step 8
- Pull the 120V armature assembly out of the diaphragm assembly.
Pull the 120V armature assembly out of the diaphragm assembly.
Step 9
- Using a metal spudger, pry the diaphgram assembly out of the gear case.
Using a metal spudger, pry the diaphgram assembly out of the gear case.
Step 10
- Now that you have loosened the diaphragm, you can now pull it out of the gear case.
Now that you have loosened the diaphragm, you can now pull it out of the gear case.
Step 11
- The diaphragm assembly will be lathered in grease. In order to move forward, you may want to give it a wipe down to remove any extra grease.
- After removing some grease (if needed), remove the two 15mm T20 Torx screws shown in red.
The diaphragm assembly will be lathered in grease. In order to move forward, you may want to give it a wipe down to remove any extra grease.
After removing some grease (if needed), remove the two 15mm T20 Torx screws shown in red.
Step 12
- Now pull the reduction gear assembly up and out of the diaphragm.
Now pull the reduction gear assembly up and out of the diaphragm.
Step 13
Diaphragm Assembly with Bushing
- Remove the metal piston from the diaphragm assembly.
Remove the metal piston from the diaphragm assembly.
Step 14
- Using a metal spudger, pry the o-ring off of the assembly.
Using a metal spudger, pry the o-ring off of the assembly.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Payton Parker
Member since: 03/08/2019
534 Reputation
2 Guides authored
Badges:
9
+6 more badges
Team
UMass Dartmouth, Team S1-G3, Botvin Spring 2019
Member of UMass Dartmouth, Team S1-G3, Botvin Spring 2019
UMASSD-BOTVIN-S19S1G3
4 Members
6 Guides authored
Javier Martinez - Nov 17, 2020
Reply
to reasemble .
Which is the correct position of the Shift knob assembly ?