Difficulty

Moderate

Steps

14

Time Required

                          45 minutes - 1 hour

Sections

1

  • Miele W4164 disassembly
  • 14 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackMiele W4164

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Miele W4164 disassembly
  • The detergent drawer is removed, push down the yellow lever to remove it completely.

The detergent drawer is removed, push down the yellow lever to remove it completely.

1024

Step 2

  • The lid has a small panel on both sides that can be levered out with a small screwdriver.

The lid has a small panel on both sides that can be levered out with a small screwdriver.

Step 3

  • There is a Tx20 screw under each of these covers, remove this.

There is a Tx20 screw under each of these covers, remove this.

Step 4

  • The cover can now be lifted at the front and then pushed back slightly. At the rear end it is only slightly hooked.

The cover can now be lifted at the front and then pushed back slightly. At the rear end it is only slightly hooked.

Step 5

  • The left side panel has three clearly visible screws at the top and three at the back, all Tx20. These must be removed. Caution, the three screws above are only identical to the bottom screw at the back, the other two screws from the back are different.

The left side panel has three clearly visible screws at the top and three at the back, all Tx20. These must be removed. Caution, the three screws above are only identical to the bottom screw at the back, the other two screws from the back are different.

Step 6

  • Remove the two Tx20 screws from the door lock.

Remove the two Tx20 screws from the door lock.

Step 7

  • Remove the Tx30 screw below the filler hole.

Remove the Tx30 screw below the filler hole.

Step 8

  • Lift the cover of the control bar slightly from behind and remove it.

Lift the cover of the control bar slightly from behind and remove it.

Step 9

  • The control panel is secured with one screw on the right side, remove this Tx20 screw.
  • Do not remove any other screws from here.

The control panel is secured with one screw on the right side, remove this Tx20 screw.

Do not remove any other screws from here.

Step 10

  • The control unit is hooked into two places, one to the right of the detergent drawer and one to the far right.
  • Carefully loosen the unit there, it is still connected with cables, so place the unit carefully on the machine.

The control unit is hooked into two places, one to the right of the detergent drawer and one to the far right.

Carefully loosen the unit there, it is still connected with cables, so place the unit carefully on the machine.

Step 11

  • The front is still attached with two Tx20 screws on the right and left, loosen them while holding the front so that it doesn’t accidentally fall down and get damaged. The front has a small hold on the right screw through the metal bracket.

The front is still attached with two Tx20 screws on the right and left, loosen them while holding the front so that it doesn’t accidentally fall down and get damaged. The front has a small hold on the right screw through the metal bracket.

Step 12

  • The front front is hooked to small feet, lift slightly to release. Make sure that the damper rubber remains on the feet. The front is still connected to the machine via the rubber boot. Keep holding the front.

The front front is hooked to small feet, lift slightly to release. Make sure that the damper rubber remains on the feet. The front is still connected to the machine via the rubber boot. Keep holding the front.

Step 13

  • Now move the front a bit so that you can loosen the 3 Tx20 screws on the left front. Then reinsert the front panel and fix it with the two upper screws. The left front can now be removed. Attention when installing the left front later, it will be hooked in at the lower end.

Now move the front a bit so that you can loosen the 3 Tx20 screws on the left front. Then reinsert the front panel and fix it with the two upper screws. The left front can now be removed. Attention when installing the left front later, it will be hooked in at the lower end.

Step 14

  • If the machine is to be operated while it is open, the door lock must be fastened first. The screw underneath the door collar has to be fastened as well.

If the machine is to be operated while it is open, the door lock must be fastened first. The screw underneath the door collar has to be fastened as well.

Work the steps in reverse order to reassemble your device.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             


        oldturkey03 is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

oldturkey03

Author

                                      with 1 other contributor 


                    kapott

Member since: 08/25/2015

1,351 Reputation

                                      7 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges