Featured
Featured Guide
Difficulty
Moderate
Steps
11
Time Required
30 minutes - 1 hour
Sections
3
- Upper Rear Panel
- 2 steps
- Lower Rear Panel
- 2 steps
- Battery & Logic Board
- 7 steps
Flags
1
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
BackMicrosoft Zune HD
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Upper Rear Panel
- Remove the four Tri-Wing screws securing the upper rear panel to the inner chassis.
Remove the four Tri-Wing screws securing the upper rear panel to the inner chassis.
1024
Step 2
- Slightly rotate the top edge of the upper rear panel away from the Zune.
- Lift the upper rear panel straight up off the black plastic lower rear panel.
Slightly rotate the top edge of the upper rear panel away from the Zune.
Lift the upper rear panel straight up off the black plastic lower rear panel.
Step 3
Lower Rear Panel
- Insert a small Zune opening tool into the gap between the logic board and one side of the black plastic lower rear panel.
- Carefully twist the Zune opening tool to pop the lower rear panel off the clips attaching it to the Zune.
- Repeat this process for the other side of the lower rear panel.
Insert a small Zune opening tool into the gap between the logic board and one side of the black plastic lower rear panel.
Carefully twist the Zune opening tool to pop the lower rear panel off the clips attaching it to the Zune.
Repeat this process for the other side of the lower rear panel.
Step 4
- Carefully slide the lower rear panel away from the Zune.
Carefully slide the lower rear panel away from the Zune.
Step 5
Battery & Logic Board
- Use a Zune opening tool to pry the digitizer ribbon cable connector up off the logic board.
Use a Zune opening tool to pry the digitizer ribbon cable connector up off the logic board.
Step 6
- Use a Zune opening tool to pry the OLED display ribbon cable connector up off the logic board.
Use a Zune opening tool to pry the OLED display ribbon cable connector up off the logic board.
Step 7
- Use a Zune opening tool to pry the control ribbon cable up off the logic board.
Use a Zune opening tool to pry the control ribbon cable up off the logic board.
Step 8
- Remove the following Torx screws securing the logic board assembly to the inner chassis:
- Three T5 Torx screws.
- One T6 Torx screw.
Remove the following Torx screws securing the logic board assembly to the inner chassis:
Three T5 Torx screws.
One T6 Torx screw.
Step 9
- Use a Zune opening tool to carefully pry the battery off the adhesive securing it to the inner chassis.
- Do not attempt to completely remove the battery from the inner chassis as it is still attached to the the logic board.
Use a Zune opening tool to carefully pry the battery off the adhesive securing it to the inner chassis.
Do not attempt to completely remove the battery from the inner chassis as it is still attached to the the logic board.
Step 10
- Use a Zune opening tool to push the small plastic clip securing the logic board near its lower left edge toward the headphone jack while gently lifting the upper edge of the logic board.
- Use a Zune opening tool to pull the plastic clip away from the logic board while gently pulling the board away from the bottom edge of the Zune.
Use a Zune opening tool to push the small plastic clip securing the logic board near its lower left edge toward the headphone jack while gently lifting the upper edge of the logic board.
Use a Zune opening tool to pull the plastic clip away from the logic board while gently pulling the board away from the bottom edge of the Zune.
Step 11
- For this step, it is recommended to cautiously hold the battery and logic board assembly with one hand while holding the inner chassis with the other.
- Pull the logic board away from the lower bezel and remove it from the inner chassis, minding any cables that may get caught.
For this step, it is recommended to cautiously hold the battery and logic board assembly with one hand while holding the inner chassis with the other.
Pull the logic board away from the lower bezel and remove it from the inner chassis, minding any cables that may get caught.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
9 other people completed this guide.
Author
with 8 other contributors
Walter Galan
682,038 Reputation
1,203 Guides authored
Badges:
54
+51 more badges
Mebradhen mere - Apr 5, 2020
Reply
thanks, dude, that was really helpful