Microsoft Surface Speakers Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 30 minutes

Sections

Back Cover
6 steps
Speakers
2 steps

Flags

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

Better Introduction

Improve this guide by completing or revising its introduction.

BackMicrosoft Surface RT
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

What you need

Step 1

              Back Cover

Prior to any repairs make sure that the device is orientated correctly, and you are familiar with all ports and buttons. The screen should be facing up with the Windows logo located on the bottom.
Turn off device prior to continuing

Prior to any repairs make sure that the device is orientated correctly, and you are familiar with all ports and buttons. The screen should be facing up with the Windows logo located on the bottom.

Turn off device prior to continuing

1024

Step 2

Carefully turn the tablet over so the screen is facing down.
Pull up on the bottom corners to open the stand.
Refer to the images.

Carefully turn the tablet over so the screen is facing down.

Pull up on the bottom corners to open the stand.

Refer to the images.

Step 3

Locate the two 5.08mm T5 Torx screws. The two screws will be located on the left and right sides in the kickstand.
Make sure when removing the screws to be careful to prevent stripping of the head.
With all the screws removed gently wiggle the stand side to side until the lever in the middle is free, releasing the stand.

Locate the two 5.08mm T5 Torx screws. The two screws will be located on the left and right sides in the kickstand.

Make sure when removing the screws to be careful to prevent stripping of the head.

With all the screws removed gently wiggle the stand side to side until the lever in the middle is free, releasing the stand.

Step 4

Use a spudger or similar flat headed tool to release the small bezels out lined in the image. Remove the plastic trim covering the camera with the soft flat headed tool.
Be patient; you will have to work around the casing because there are several small bezels along the edges.

Use a spudger or similar flat headed tool to release the small bezels out lined in the image. Remove the plastic trim covering the camera with the soft flat headed tool.

Be patient; you will have to work around the casing because there are several small bezels along the edges.

Step 5

Next, remove the ten 5.92mm T5 torx screws located underneath the kickstand.
Remove the seven 5.87mm T5 torx screws located under the camera casing. There is a sticker covering the second screw from the left.
Disconnect the rear cover from the main shell of the system by loosening it with a spudger where the gaps exist.
There is an electrical ribbon connecting the rear cover to the motherboard. Do not pull apart the rear cover from the motherboard once you have loosened the rear cover from the main system.
Continue working your way around to each corner and loosen the snap-ons on each side until the rear cover comes off.

Next, remove the ten 5.92mm T5 torx screws located underneath the kickstand.

Remove the seven 5.87mm T5 torx screws located under the camera casing. There is a sticker covering the second screw from the left.

Disconnect the rear cover from the main shell of the system by loosening it with a spudger where the gaps exist.

There is an electrical ribbon connecting the rear cover to the motherboard. Do not pull apart the rear cover from the motherboard once you have loosened the rear cover from the main system.

Continue working your way around to each corner and loosen the snap-ons on each side until the rear cover comes off.

Step 6

Rotate the device 180 degrees so that the bottom of the device is facing you.
A ribbon connects the battery on the rear cover, to the motherboard. Slowly lift the bottom of the rear cover up until you can see the ribbon.
Use a spudger to push the ribbon away from the motherboard and parallel to the motherboard in order to remove the ribbon.
Separate the rear cover by lifting it up away from the main system.
When reassembling the rear cover to the motherboard, reinserting the ribbon cable with a spudger may prove difficult. In this case, gently use your hands to slide the cable end into the slot until they click into place.

Rotate the device 180 degrees so that the bottom of the device is facing you.

A ribbon connects the battery on the rear cover, to the motherboard. Slowly lift the bottom of the rear cover up until you can see the ribbon.

Use a spudger to push the ribbon away from the motherboard and parallel to the motherboard in order to remove the ribbon.

Separate the rear cover by lifting it up away from the main system.

When reassembling the rear cover to the motherboard, reinserting the ribbon cable with a spudger may prove difficult. In this case, gently use your hands to slide the cable end into the slot until they click into place.

Step 7

              Speakers

Use a spudger to remove the orange ribbon connected to the motherboard located on the left.
Locate the two speakers.

Use a spudger to remove the orange ribbon connected to the motherboard located on the left.

Locate the two speakers.

Step 8

On the motherboard, locate where the orange ribbon of the speakers is connected to the motherboard and flip the white switch upwards so that it is perpendicular to the motherboard.
Both speakers need to be detached the same way. This will allow the the speakers to be detached easier.
Loosen the speakers from the motherboard using a spudger.
Gently pull out the speaker’s electrical ribbon from the motherboard for both speakers.

On the motherboard, locate where the orange ribbon of the speakers is connected to the motherboard and flip the white switch upwards so that it is perpendicular to the motherboard.

Both speakers need to be detached the same way. This will allow the the speakers to be detached easier.

Loosen the speakers from the motherboard using a spudger.

Gently pull out the speaker’s electrical ribbon from the motherboard for both speakers.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors

                    Kevin Hua

Member since: 01/11/2013

1,533 Reputation

                                      3 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       Cal Poly, Team 17-23, Forte Winter 2013                        

                                                  Member of Cal Poly, Team 17-23, Forte Winter 2013 



                    CPSU-FORTE-W13S17G23                     


                                            5 Members                     


                                            15 Guides authored

Action Shots#

Needs Better Images#

Markup Mishap#

Better Introduction#

What you need#

Team#