Microsoft Surface Pro 6 Left Speaker Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          45 minutes - 2 hours

Sections

Microsoft Surface Pro 6 Opening Procedure
22 steps
Antenna Support
3 steps
Heat Sink
5 steps
Volume and Power Buttons
8 steps
Left Speaker
1 step

Flags

BackMicrosoft Surface Pro 6
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Applying new thermal paste to the CPU during reassembly may improve the performance of your Surface. If you wish to do that, make sure you have new thermal paste and either high-concentration isopropyl alcohol or a specialized thermal paste cleaner.

There is a significant chance that you may break the unreinforced and fragile display panel during this procedure. Be sure to apply plenty of heat and be extremely careful during the prying stage.

What you need

Step 1

              Heat the screen

Completely power off the Surface before you begin disassembly.
If the screen’s glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping over the glass. Lay overlapping strips of clear packing tape over the display until all the glass is covered. Wear safety glasses to protect your eyes.
Heat an iOpener and apply it to the right edge of the Surface’s screen for two minutes.
You may need to reheat and reapply the iOpener several times to get the Surface warm enough. Follow the iOpener instructions to avoid overheating.
A hair dryer, heat gun, or hot plate may also be used for more heat, but be careful not to overheat the Surface—the screen and internal battery are susceptible to heat damage.

Completely power off the Surface before you begin disassembly.

If the screen’s glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping over the glass. Lay overlapping strips of clear packing tape over the display until all the glass is covered. Wear safety glasses to protect your eyes.

Heat an iOpener and apply it to the right edge of the Surface’s screen for two minutes.

You may need to reheat and reapply the iOpener several times to get the Surface warm enough. Follow the iOpener instructions to avoid overheating.

A hair dryer, heat gun, or hot plate may also be used for more heat, but be careful not to overheat the Surface—the screen and internal battery are susceptible to heat damage.

1024

Step 2

              Take note of the adhesive layout

Take note of the screen adhesive layout before continuing:
These areas only contain adhesive and are safe to cut.
The display board and flex cables sit here close to the edge. Cut very carefully and do not insert the pick as deep under the display.
Fragile antenna cables lie under this part of the screen. Carefully follow the procedure to avoid damaging them. The adhesive is also the thickest here.

Take note of the screen adhesive layout before continuing:

These areas only contain adhesive and are safe to cut.

The display board and flex cables sit here close to the edge. Cut very carefully and do not insert the pick as deep under the display.

Fragile antenna cables lie under this part of the screen. Carefully follow the procedure to avoid damaging them. The adhesive is also the thickest here.

Step 3

              Insert an opening pick into the speaker opening

Insert an opening pick into the speaker opening on the screen and slide the pick under the glass. Do not press the pick into the speaker grille, as the grille is easily torn.
Don’t insert the opening pick any deeper than the black bezel on the side of the screen. Inserting the pick too far may damage the LCD.

Insert an opening pick into the speaker opening on the screen and slide the pick under the glass. Do not press the pick into the speaker grille, as the grille is easily torn.

Don’t insert the opening pick any deeper than the black bezel on the side of the screen. Inserting the pick too far may damage the LCD.

Step 4

              Slide an opening pick under the screen

Rotate the pick toward the bottom of the Surface to slide it underneath the lower edge of the speaker cutout.

Rotate the pick toward the bottom of the Surface to slide it underneath the lower edge of the speaker cutout.

Step 5

              Cut through the screen adhesive

Slide the pick down the right edge of the Surface to slice through the adhesive under the screen.
Throughout the rest of the procedure, if you encounter significant resistance while sliding the pick, stop and reheat the section you’re working on. Applying too much pressure with the pick can crack the glass.
Leave this opening pick in the right edge to prevent the adhesive from resealing.

Slide the pick down the right edge of the Surface to slice through the adhesive under the screen.

Throughout the rest of the procedure, if you encounter significant resistance while sliding the pick, stop and reheat the section you’re working on. Applying too much pressure with the pick can crack the glass.

Leave this opening pick in the right edge to prevent the adhesive from resealing.

Step 6

Reheat the iOpener and apply it to the bottom edge of the Surface’s screen for two minutes.
You may need to reheat and reapply the iOpener several times to get the Surface warm enough. Follow the iOpener instructions to avoid overheating.
A hair dryer, heat gun, or hot plate may also be used for more heat, but be careful not to overheat the Surface—the screen and internal battery are susceptible to heat damage.

Reheat the iOpener and apply it to the bottom edge of the Surface’s screen for two minutes.

Step 7

Insert a new opening pick into the bottom right corner and slide it around the corner toward the bottom edge.
Don’t insert the opening pick any deeper than the black bezel on the side of the screen. Inserting the pick too far may damage the LCD.
Slide the pick along the bottom edge of the Surface to cut through the screen adhesive.
Leave this pick in the bottom edge to prevent the adhesive from resealing.

Insert a new opening pick into the bottom right corner and slide it around the corner toward the bottom edge.

Slide the pick along the bottom edge of the Surface to cut through the screen adhesive.

Leave this pick in the bottom edge to prevent the adhesive from resealing.

Step 8

Reheat the iOpener and apply it to the left edge of the Surface’s screen for two minutes.
You may need to reheat and reapply the iOpener several times to get the Surface warm enough. Follow the iOpener instructions to avoid overheating.
A hair dryer, heat gun, or hot plate may also be used for more heat, but be careful not to overheat the Surface—the screen and internal battery are susceptible to heat damage.

Reheat the iOpener and apply it to the left edge of the Surface’s screen for two minutes.

Step 9

Insert a new opening pick into the bottom left corner and slide it around the corner toward the left edge.
Take care cutting under the lower 2.5 inches (65 mm) of the left edge. Do not insert the opening pick more than 1/8 inches (3 mm) here. The display cables sit near this part of the bezel and are easily damaged. Once past the display cable area, do not insert the pick past the bezel.
Slide the pick along the left edge of the Surface to cut through the screen adhesive.
Leave this pick in the left edge to prevent the adhesive from resealing.

Insert a new opening pick into the bottom left corner and slide it around the corner toward the left edge.

Take care cutting under the lower 2.5 inches (65 mm) of the left edge. Do not insert the opening pick more than 1/8 inches (3 mm) here. The display cables sit near this part of the bezel and are easily damaged. Once past the display cable area, do not insert the pick past the bezel.

Slide the pick along the left edge of the Surface to cut through the screen adhesive.

Leave this pick in the left edge to prevent the adhesive from resealing.

Step 10

Reheat the iOpener and apply it to the top edge of the Surface’s screen for two minutes.
The adhesive is thickest along this edge, and you may need to reheat and reapply the iOpener several times to get the Surface warm enough. Follow the iOpener instructions to avoid overheating.
A hair dryer, heat gun, or hot plate may also be used for more heat, but be careful not to overheat the Surface—the screen and internal battery are susceptible to heat damage.

Reheat the iOpener and apply it to the top edge of the Surface’s screen for two minutes.

The adhesive is thickest along this edge, and you may need to reheat and reapply the iOpener several times to get the Surface warm enough. Follow the iOpener instructions to avoid overheating.

Step 11

Round the left corner with the opening pick and slide it along the top edge of the Surface. Stop when the pick is 2.75 inches (70 mm) away from the left edge.
The next 6 inches (15 cm) of the top edge of the case is covered by the left and right antennas, which sit between the case and the screen bezel. Follow the next steps carefully to avoid damaging the antennas.

Round the left corner with the opening pick and slide it along the top edge of the Surface. Stop when the pick is 2.75 inches (70 mm) away from the left edge.

The next 6 inches (15 cm) of the top edge of the case is covered by the left and right antennas, which sit between the case and the screen bezel. Follow the next steps carefully to avoid damaging the antennas.

Step 12

Insert the point of a pick under the display where you just stopped cutting. Do not insert the pick deeper than the edge of the bezel.
Carefully roll the pick to the right, pressing the long edge of the pick into the screen adhesive underneath the bezel, cutting the adhesive as you go. Do not slide the pick along the edge of the Surface.
Keep the pick parallel to the screen throughout the whole procedure so that it doesn’t catch on the antennas. Do not press the pick against the case.
Repeat this motion of inserting the point of the pick where you just cut, and rolling to the right all along the top edge of the Surface, until the pick is 2.5 inches (64 mm) from the right edge of the Surface.

Insert the point of a pick under the display where you just stopped cutting. Do not insert the pick deeper than the edge of the bezel.

Carefully roll the pick to the right, pressing the long edge of the pick into the screen adhesive underneath the bezel, cutting the adhesive as you go. Do not slide the pick along the edge of the Surface.

Keep the pick parallel to the screen throughout the whole procedure so that it doesn’t catch on the antennas. Do not press the pick against the case.

Repeat this motion of inserting the point of the pick where you just cut, and rolling to the right all along the top edge of the Surface, until the pick is 2.5 inches (64 mm) from the right edge of the Surface.

Step 13

Once you cut the adhesive over the antennas (8.5 inches, or 22 cm, away from the left edge), slide the pick the rest of the way along the top edge of the surface and round the top right corner to slice through any remaining adhesive.

Once you cut the adhesive over the antennas (8.5 inches, or 22 cm, away from the left edge), slide the pick the rest of the way along the top edge of the surface and round the top right corner to slice through any remaining adhesive.

Step 14

              Open the Surface

Very slowly lift the screen assembly away from the Surface case. If you encounter any resistance, stop and check that all the adhesive is separated.
Do not remove the screen yet. It is still connected to the motherboard by two cables.
Use an opening pick to cut through any remaining adhesive.
The flash lens may fall out of the Surface case. Keep track of the lens and return it to its cutout in the case during reassembly.

Very slowly lift the screen assembly away from the Surface case. If you encounter any resistance, stop and check that all the adhesive is separated.

Do not remove the screen yet. It is still connected to the motherboard by two cables.

Use an opening pick to cut through any remaining adhesive.

The flash lens may fall out of the Surface case. Keep track of the lens and return it to its cutout in the case during reassembly.

Step 15

Lift the top of the screen assembly away from the case while sliding the bottom of the screen closer to the motherboard display connectors.
Gently lay the screen down on the case with the connectors facing up. Take care to avoid creasing the display cables.

Lift the top of the screen assembly away from the case while sliding the bottom of the screen closer to the motherboard display connectors.

Gently lay the screen down on the case with the connectors facing up. Take care to avoid creasing the display cables.

Step 16

              Disconnect the screen

Use an opening pick to pry up one edge of the EMI shield covering the display board.
Repeat this procedure at different points around the shield until it is free.
Try not to deform the shield too much—you will need to reinstall it during reassembly.

Use an opening pick to pry up one edge of the EMI shield covering the display board.

Repeat this procedure at different points around the shield until it is free.

Try not to deform the shield too much—you will need to reinstall it during reassembly.

Step 17

Lift the EMI shield away from the display board and remove it.

Lift the EMI shield away from the display board and remove it.

Step 18

Use the flat end of a spudger to pry the display interconnect cable straight up and out of its socket on the board.

Use the flat end of a spudger to pry the display interconnect cable straight up and out of its socket on the board.

Step 19

Insert one point of a pair of pointed tweezers into a gap in the edge of the EMI shield covering the digitizer connector.
Use the tweezers to pry the EMI shield away from the display as much as you can without bending it.
Repeat this procedure at different points around the shield until it is free. Remove the shield.
Try not to deform the shield too much—you will need to reinstall it during reassembly.

Insert one point of a pair of pointed tweezers into a gap in the edge of the EMI shield covering the digitizer connector.

Use the tweezers to pry the EMI shield away from the display as much as you can without bending it.

Repeat this procedure at different points around the shield until it is free. Remove the shield.

Step 20

Pull the rest of the shield off of the digitizer connector and remove it.

Pull the rest of the shield off of the digitizer connector and remove it.

Step 21

Use the tip of a spudger to pry the digitizer connector straight up and out of its socket on the screen.

Use the tip of a spudger to pry the digitizer connector straight up and out of its socket on the screen.

Step 22

Remove the screen assembly from the Surface.
During reassembly, pause here and follow this guide to replace the screen adhesive.

Remove the screen assembly from the Surface.

During reassembly, pause here and follow this guide to replace the screen adhesive.

Step 23

              Disconnect the antenna support

Use the point of a spudger to pry the microphone connector straight up and out of its socket on the motherboard.

Use the point of a spudger to pry the microphone connector straight up and out of its socket on the motherboard.

Step 24

              Unscrew the antenna support

Use a T5 Torx driver to remove the four screws securing the antenna support:
Three 4.5 mm screws
One 6 mm screw

Use a T5 Torx driver to remove the four screws securing the antenna support:

Three 4.5 mm screws

One 6 mm screw

Step 25

              Remove the antenna support

Use a spudger to lift the antenna support out of its recess in the Surface.
Remove the antenna support.

Use a spudger to lift the antenna support out of its recess in the Surface.

Remove the antenna support.

Step 26

              Remove the heat sink shield

Insert one point of a pair of pointed tweezers into a gap in the corner of the EMI shield covering the heat sink.
Use the tweezers to pry the EMI shield away from the motherboard as much as you can without bending it. Do not remove it yet.
Try not to deform the shield too much—you will need to reinstall it during reassembly.
Take care not to puncture the battery with the tweezers while working on this shield.

Insert one point of a pair of pointed tweezers into a gap in the corner of the EMI shield covering the heat sink.

Use the tweezers to pry the EMI shield away from the motherboard as much as you can without bending it. Do not remove it yet.

Take care not to puncture the battery with the tweezers while working on this shield.

Step 27

Repeat the last step for each corner of the EMI shield covering the heat sink.

Repeat the last step for each corner of the EMI shield covering the heat sink.

Step 28

Remove the heat sink shield.

Remove the heat sink shield.

Step 29

              Remove the heat sink

Remove the ten Torx screws securing the heat sink:
Six 2.6 mm-long T3 screws
Four 3.3 mm-long T5 screws
During reassembly, tighten the heat sink screws in the following criss-cross pattern, one turn at a time, until they’re tight:
Screw 1
Screw 2
Screw 3
Screw 4

Remove the ten Torx screws securing the heat sink:

Six 2.6 mm-long T3 screws

Four 3.3 mm-long T5 screws

During reassembly, tighten the heat sink screws in the following criss-cross pattern, one turn at a time, until they’re tight:

Screw 1

Screw 2

Screw 3

Screw 4

Step 30

Use a spudger to gently pry the heat sink straight up and off of the CPU.
Take care not to dent or crease the heat sink pipes during removal.
During reassembly, make sure to properly clean the heat sink and CPU, and apply new thermal paste.

Use a spudger to gently pry the heat sink straight up and off of the CPU.

Take care not to dent or crease the heat sink pipes during removal.

During reassembly, make sure to properly clean the heat sink and CPU, and apply new thermal paste.

Step 31

              Disconnect the left speaker

Use the point of a spudger to lift the left speaker connector out of its socket on the motherboard.

Use the point of a spudger to lift the left speaker connector out of its socket on the motherboard.

Step 32

              Disconnect the volume and power buttons

Use the point of a spudger to flip up the small locking flap securing the volume and power button cable ZIF connector.
Slide the volume and power button cable straight out of its socket on the motherboard.

Use the point of a spudger to flip up the small locking flap securing the volume and power button cable ZIF connector.

Slide the volume and power button cable straight out of its socket on the motherboard.

Step 33

              Remove the left speaker assembly

Use a T5 Torx driver to remove the two screws securing the left speaker:
One 6 mm screw
One 3.9 mm screw

Use a T5 Torx driver to remove the two screws securing the left speaker:

One 3.9 mm screw

Step 34

Use a spudger to lift the right edge of the speaker so that it clears the motherboard and screw bosses.
With the right edge lifted, slide the speaker to the right, straight out of its recess in the case.

Use a spudger to lift the right edge of the speaker so that it clears the motherboard and screw bosses.

With the right edge lifted, slide the speaker to the right, straight out of its recess in the case.

Step 35

              Remove the volume and power button assembly

Heat an iOpener and apply it to the long edge of the speaker assembly for two minutes to soften the adhesive securing the buttons.

Heat an iOpener and apply it to the long edge of the speaker assembly for two minutes to soften the adhesive securing the buttons.

Step 36

Slide an opening pick under the volume and power button cable to separate the adhesive securing the cable to the speaker.

Slide an opening pick under the volume and power button cable to separate the adhesive securing the cable to the speaker.

Step 37

Slide an opening pick under the volume and power buttons to separate the adhesive securing the buttons to the speaker.

Slide an opening pick under the volume and power buttons to separate the adhesive securing the buttons to the speaker.

Step 38

Remove the volume and power buttons.

Remove the volume and power buttons.

Step 39

              Remove the left speaker

Only the left speaker remains.

Only the left speaker remains.

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for troubleshooting help.

Cancel: I did not complete this guide.

Author

                    Adam O'Camb

Member since: 04/11/2015

173,479 Reputation

                                      418 Guides authored                  



                       Badges:
                       39







                                                        +36 more badges

Introduction#

What you need#

Introduction

What you need