Microsoft Surface Pro 3 Rear Facing Camera Replacement Repair Guide

Difficulty

Very difficult

Steps

Time Required

                          1 - 2 hours

Sections

Display
7 steps
Rear Facing Camera
4 steps

Flags

BackMicrosoft Surface Pro 3
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Display

Before you begin, discharge the Surface Pro’s battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally damaged during the repair.
The display is strongly glued to the frame of the device.
To remove the display, first soften the adhesive by applying heat. You can use a heat pad, heat gun, or iOpener. In a pinch, a hair dryer can also work.
Be careful when using a heat gun, as too much heat can permanently damage the display and/or battery.
Steadily and evenly heat the perimeter of the display until it’s too hot to touch, and try to maintain that temperature for several minutes.

Before you begin, discharge the Surface Pro’s battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally damaged during the repair.

The display is strongly glued to the frame of the device.

To remove the display, first soften the adhesive by applying heat. You can use a heat pad, heat gun, or iOpener. In a pinch, a hair dryer can also work.

Be careful when using a heat gun, as too much heat can permanently damage the display and/or battery.

Steadily and evenly heat the perimeter of the display until it’s too hot to touch, and try to maintain that temperature for several minutes.

1024

Step 2

Use a suction cup or an iSclack to pull up on the glass and create a slight gap between the glass and the metal frame.
If your display is badly cracked, a suction cup may not adhere. It may help to first cover the display with a layer of packing tape. Alternatively, you can superglue your suction cup to the display.
Carefully insert an opening pick into the gap between the screen and the device to cut the adhesive.
Slide the pick around the sides and bottom of the display to cut the adhesive. Apply more heat as needed.
Work carefully—the glass is thin and will crack easily if you try to force it.
The wi-fi antennas are glued under the screen border along the top edge (on either side of the camera), and can be damaged easily. Use extra care when separating the top edge, and apply more heat if necessary.

Use a suction cup or an iSclack to pull up on the glass and create a slight gap between the glass and the metal frame.

If your display is badly cracked, a suction cup may not adhere. It may help to first cover the display with a layer of packing tape. Alternatively, you can superglue your suction cup to the display.

Carefully insert an opening pick into the gap between the screen and the device to cut the adhesive.

Slide the pick around the sides and bottom of the display to cut the adhesive. Apply more heat as needed.

Work carefully—the glass is thin and will crack easily if you try to force it.

The wi-fi antennas are glued under the screen border along the top edge (on either side of the camera), and can be damaged easily. Use extra care when separating the top edge, and apply more heat if necessary.

Step 3

Continue to heat sections of the screen with the heat gun.
As you make your way around the screen with the heat gun, use the plastic opening tool and the opening picks to pry the screen loose.
The screen is extremely thin and very easy to break. Be careful working with broken glass.

Continue to heat sections of the screen with the heat gun.

As you make your way around the screen with the heat gun, use the plastic opening tool and the opening picks to pry the screen loose.

The screen is extremely thin and very easy to break. Be careful working with broken glass.

Step 4

Lift the screen up carefully so that no wires are torn.

Lift the screen up carefully so that no wires are torn.

Step 5

Remove the 3 mm T3 Torx screw securing the battery connector, and disconnect the battery connector.
Be careful not lose the small, rectangular bridge connector that lies underneath.

Remove the 3 mm T3 Torx screw securing the battery connector, and disconnect the battery connector.

Be careful not lose the small, rectangular bridge connector that lies underneath.

Step 6

Remove the single 4 mm T3 Torx screw securing the display cable.
Lift the connector to disconnect the cable.
Be careful not lose the small, rectangular bridge connector that lies underneath.

Remove the single 4 mm T3 Torx screw securing the display cable.

Lift the connector to disconnect the cable.

Step 7

Grasp the orange cable connected to the silver connecter.
Carefully lift the orange cable up until the connecter pops off.
The screen will now be completely disconnected.
The replacement display may not include all the parts needed for installation. Save all the parts from the original display, and transfer them to the new display as needed.

Grasp the orange cable connected to the silver connecter.

Carefully lift the orange cable up until the connecter pops off.

The screen will now be completely disconnected.

The replacement display may not include all the parts needed for installation. Save all the parts from the original display, and transfer them to the new display as needed.

Step 8

              Rear Facing Camera

Remove the 4mm screw with the T3 Torx Screwdriver.
Remove the four 7mm screws with the T3 Torx Screwdriver.

Remove the 4mm screw with the T3 Torx Screwdriver.

Remove the four 7mm screws with the T3 Torx Screwdriver.

Step 9

Locate the black piece shown.
Remove this piece by gently lifting it up with the tweezers until it pops off.

Locate the black piece shown.

Remove this piece by gently lifting it up with the tweezers until it pops off.

Step 10

Remove the two 4mm screws with the T5 Torx Screwdriver.

Remove the two 4mm screws with the T5 Torx Screwdriver.

Step 11

Remove the rear camera with the tweezers.

Remove the rear camera with the tweezers.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 5 other contributors

                    Erik Snyder

Member since: 10/01/2015

5,006 Reputation

                                      5 Guides authored                  



                       Badges:
                       17







                                                        +14 more badges

Team

                       Cal Poly, Team 12-18, Maness Fall 2015                        

                                                  Member of Cal Poly, Team 12-18, Maness Fall 2015 



                    CPSU-MANESS-F15S12G18                     


                                            5 Members                     


                                            31 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team