Difficulty

Moderate

Steps

13

Time Required

                          5 - 15 minutes

Sections

3

  • How to Detach the Keyboard on a Surface Book
  • 7 steps
  • Back Panel
  • 3 steps
  • SD Card Reader
  • 3 steps

Flags

0

  • BackMicrosoft Surface Book

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

The Realtek RTS5314 SD card reader, located near the two USB ports, is easy to remove and replace. Make sure that you have a place to hold onto the tiny screws as you remove them.

What you need

Step 1

              Remove the display with the Detach button
  • In order for the keyboard to be detached with the Detach buttons, both batteries must be charged above 10 percent. If your device doesn’t power on and you can’t use the Detach buttons, skip to the next step.
  • Press and hold the Detach button on the keyboard.
  • Once pressed, the Detach button it will light up red. After a second, it’ll turn green and you’ll hear an audible clicking sound.
  • Alternatively, click the Detach icon on the right-hand side of the Windows 10 taskbar.
  • Remove the display.

In order for the keyboard to be detached with the Detach buttons, both batteries must be charged above 10 percent. If your device doesn’t power on and you can’t use the Detach buttons, skip to the next step.

Press and hold the Detach button on the keyboard.

Once pressed, the Detach button it will light up red. After a second, it’ll turn green and you’ll hear an audible clicking sound.

Alternatively, click the Detach icon on the right-hand side of the Windows 10 taskbar.

Remove the display.

1024

Step 2

              Manually detach the display
  • The next six steps show how to detach the display manually if you’re unable to power on the Surface Book.
  • Flip open the display as far as it will go.
  • Lift the device up and place it on its side, with the display facing away from you and the SurfaceConnect port facing up.

The next six steps show how to detach the display manually if you’re unable to power on the Surface Book.

Flip open the display as far as it will go.

Lift the device up and place it on its side, with the display facing away from you and the SurfaceConnect port facing up.

Step 3

              Bend a paper clip
  • Straighten out one section of a paper clip.

Straighten out one section of a paper clip.

Step 4

              Push the paper clip into the hole
  • The Surface Book has an internal lever arm mechanism that can be manually actuated through an access hole in the vents on side of the display.
  • Insert the straight end of the paper clip at a 45 degree angle into the sixth hole from the left.

The Surface Book has an internal lever arm mechanism that can be manually actuated through an access hole in the vents on side of the display.

Insert the straight end of the paper clip at a 45 degree angle into the sixth hole from the left.

Step 5

              Release the mechanism
  • Firmly push the paper clip into the hole.
  • This may take a considerable amount of force.
  • Once the internal lever arm is fully depressed, you can disconnect the display.
  • Pull the base away from the display to detach it.
  • If you are unable to detach the display from the base on this side, release pressure on the paper clip and try again.

Firmly push the paper clip into the hole.

This may take a considerable amount of force.

Once the internal lever arm is fully depressed, you can disconnect the display.

Pull the base away from the display to detach it.

If you are unable to detach the display from the base on this side, release pressure on the paper clip and try again.

Step 6

              Detach the second side
  • The magnetic connections are prone to snap back into place, so hold the two halves apart.
  • With one side detached, pull firmly to pivot the display out to disconnect the second side.
  • If the magnetic connection feels extra strong and the display won’t detach on the second side, keep the detached side separated with a spudger, pen, or pencil, and repeat the paper clip process on the other side of the display.

The magnetic connections are prone to snap back into place, so hold the two halves apart.

With one side detached, pull firmly to pivot the display out to disconnect the second side.

If the magnetic connection feels extra strong and the display won’t detach on the second side, keep the detached side separated with a spudger, pen, or pencil, and repeat the paper clip process on the other side of the display.

Step 7

              Remove the display
  • Remove the display.
  • Completely power down your Surface Book before opening it up for any repairs.

Completely power down your Surface Book before opening it up for any repairs.

Step 8

              Back Panel
  • Flip the keyboard over so you can see the back panel.

Flip the keyboard over so you can see the back panel.

Step 9

  • Insert the plastic opening tool in the crevice between the panel and the keyboard.
  • Apply some pressure and lift up so that the back panel is pried away from the keyboard.
  • The panel is glued down on the inside so this may require some force to lift away the panel.
  • Continue to lift until the panel is completely separated from the keyboard.
  • The panel is still attached to the keyboard by a ribbon cable so only lift the panel a few inches.

Insert the plastic opening tool in the crevice between the panel and the keyboard.

Apply some pressure and lift up so that the back panel is pried away from the keyboard.

The panel is glued down on the inside so this may require some force to lift away the panel.

Continue to lift until the panel is completely separated from the keyboard.

The panel is still attached to the keyboard by a ribbon cable so only lift the panel a few inches.

Step 10

  • Lift the panel away with the ribbon cable still attached and set aside the panel so that you can work on other components.

Lift the panel away with the ribbon cable still attached and set aside the panel so that you can work on other components.

Step 11

              SD Card Reader
  • Orient your keyboard with the internals facing up and the USB ports on the right.

Orient your keyboard with the internals facing up and the USB ports on the right.

Step 12

  • Use the T3 screwdriver to remove the two 4 mm screws on the right side of the SD Card Reader.

Use the T3 screwdriver to remove the two 4 mm screws on the right side of the SD Card Reader.

Step 13

  • Remove the black ribbon cable tab on the SD card reader from the chip with a plastic opening tool. Place the tool underneath the tab and pry it off.
  • Removing this tab can be a little difficult. Be sure that you have a good angle and do not get discouraged if removing the tab takes you multiple tries.
  • Lift the SD card reader away from the keyboard to replace it.

Remove the black ribbon cable tab on the SD card reader from the chip with a plastic opening tool. Place the tool underneath the tab and pry it off.

Removing this tab can be a little difficult. Be sure that you have a good angle and do not get discouraged if removing the tab takes you multiple tries.

Lift the SD card reader away from the keyboard to replace it.

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors 


                    Natalie Weisenburger

Member since: 10/06/2016

581 Reputation

                                      4 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       Cal Poly, Team 20-3, Livingston Fall 2016                        

                                                  Member of Cal Poly, Team 20-3, Livingston Fall 2016 



                    CPSU-LIVINGSTON-F16S20G3                     


                                            4 Members                     


                                            12 Guides authored

Trent Fowler - Nov 27, 2017

Reply

Awesome guide! Do you know where to find a replacement module?