Difficulty
Very difficult
Steps
10
Time Required
25 minutes
Sections
3
- Back Cover / Rear Case
- 3 steps
- Logic board
- 2 steps
- Touch Screen Glass, LCD Display
- 5 steps
Flags
1
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackMicrosoft Lumia 535
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
RM-1090 / RM-1091/ RM-1089 / RM-1092
How to disassemble the phone and replace broken, smashed Display or Touch Screen Glass Digitizer.
!!!There are different versions touch screens:
• CT2S1973FPC-A1-E
• CT2C1607FPC-A1-E
The version is printed on the flex cable.
What you need
Video Overview
Step 1
Back Cover / Rear Case
- Turn off the phone.
- Remove the battery and any SIM and memory cards.
Turn off the phone.
Remove the battery and any SIM and memory cards.
1024
Step 2
- With a screwdriver Torx T4 remove the 9x screws.
With a screwdriver Torx T4 remove the 9x screws.
Step 3
- With a plastic opening tool separate the back cover from the middle frame.
With a plastic opening tool separate the back cover from the middle frame.
Step 4
Logic board
- Disconnect:
- Touch screen flex cable
- LCD Display flex cable
- Charging Dock board flex cable - remove the foam and tape, then flip up the black lock before easing out the flex.
- Coaxial antena cable - take your time here, be sure to pull the metal connector and not the cable or you risk pulling the cable from the connector.
- Remove the 2x Torx T4 screws.
Disconnect:
Touch screen flex cable
LCD Display flex cable
Charging Dock board flex cable - remove the foam and tape, then flip up the black lock before easing out the flex.
Coaxial antena cable - take your time here, be sure to pull the metal connector and not the cable or you risk pulling the cable from the connector.
Remove the 2x Torx T4 screws.
Step 5
- Insert wisdom here.
Insert wisdom here.
Step 6
Touch Screen Glass, LCD Display
- Remove the display flex cable rubber.
- Put scotch tape on glass to prevent it from shattering.
- Use a hair dryer or heat gun and warm the glass to make adhesive soft.
Remove the display flex cable rubber.
Put scotch tape on glass to prevent it from shattering.
Use a hair dryer or heat gun and warm the glass to make adhesive soft.
Step 7
- Use a cutter or other tool with a sharp edge and start the separating from the bottom side. When you make enough room, continue the operation with a plastic tool.
- Work slowly and do not force the frame with the display too much.
- If necessary, warm again the glass with a hairdryer.
Use a cutter or other tool with a sharp edge and start the separating from the bottom side. When you make enough room, continue the operation with a plastic tool.
Work slowly and do not force the frame with the display too much.
If necessary, warm again the glass with a hairdryer.
Step 8
- Using a plastic tool, carefully remove the display.
- Clean the frame from the remainders of the old adhesive.
Using a plastic tool, carefully remove the display.
Clean the frame from the remainders of the old adhesive.
Step 9
- Install back the display.
- Put adhesive tape 2mm on the digitizer.
- Order the digitizer glass together with an adhesive tape. The replacement is easier.
Install back the display.
Put adhesive tape 2mm on the digitizer.
Order the digitizer glass together with an adhesive tape. The replacement is easier.
Step 10
- Install the touch screen and start with the reassembling.
- That’s all.
- .
- .
- .
- .
- .
- Did you do it successfully?
Install the touch screen and start with the reassembling.
That’s all.
.
Did you do it successfully?
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
50 other people completed this guide.
Author
with 2 other contributors
ZFix
Member since: 12/09/2013
187,195 Reputation
330 Guides authored
Badges:
35
+32 more badges
Team
Master Techs
Member of Master Techs
Community
310 Members
1,168 Guides authored
omarkhalil - Apr 3, 2016
Reply
hi
cane you tell me price of out glass of lumia 535 duol sim please ?!
Jithu - Apr 28, 2016
Reply
2mm adhesive tape means thickness
Also does touch come out if we put adhesive tape.
Saikrishna - May 10, 2016
Reply
I want to join in your team
priscilaalmerinda - Jun 13, 2016
Reply
Hi,How to know which the versions touch screens my phone is Lumia 535 RM-1089 , please?