Difficulty
Moderate
Steps
10
Time Required
25 minutes
Sections
4
- Back Cover
- 2 steps
- Logic board
- 2 steps
- LCD Display
- 3 steps
- Touch screen Glass Only
- 3 steps
Flags
1
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackMicrosoft Lumia 435
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
Lumia 532 RM-1032, RM1034
How to disassemble Lumia 435, Lumia 532 and replace the broken touch screen glass.
What you need
Video Overview
Step 1
Back Cover
- Switch off the phone.
- Remove the battery and any inserted SIM and memory cards.
- Use a screwdriver Torx T6 and remove the 4x black screws.
Switch off the phone.
Remove the battery and any inserted SIM and memory cards.
Use a screwdriver Torx T6 and remove the 4x black screws.
1024
Step 2
- There are several plastic locking clips hold the back cover to the frame.
- Use a tool with a sharp edge to unlock them and a plastic tool to separate the back cover.
There are several plastic locking clips hold the back cover to the frame.
Use a tool with a sharp edge to unlock them and a plastic tool to separate the back cover.
Step 3
Logic board
- Unhook:
- the touch screen flex cable
- the LCD Display flex cable
- Use a plastic tool lift up and remove the Logic board.
Unhook:
the touch screen flex cable
the LCD Display flex cable
Use a plastic tool lift up and remove the Logic board.
Step 4
- This is the logic board / main board - a front and rear view.
This is the logic board / main board - a front and rear view.
Step 5
LCD Display
- The Display metal shield is locked to the frame by 4x locking clips.
- Use a tool with a sharp tip and careful unlock them and remove the shield.
The Display metal shield is locked to the frame by 4x locking clips.
Use a tool with a sharp tip and careful unlock them and remove the shield.
Step 6
- The display is stuck tovthe touch screen glass with a double-sided adhesive tape.
- Use a hair dryer or hot air gun and worm the glass to make adhesive soften.
- Distort the frame a little and use a thin plastic tool to separate the display from the frame.
The display is stuck tovthe touch screen glass with a double-sided adhesive tape.
Use a hair dryer or hot air gun and worm the glass to make adhesive soften.
Distort the frame a little and use a thin plastic tool to separate the display from the frame.
Step 7
- The display is very fragile, do the separation very carefully.
The display is very fragile, do the separation very carefully.
Step 8
Touch screen Glass Only
- Put some transparent scotch tape to prevent the glass from shattering.
- Warm the glass for a minute to make adhesive soften.
- Start the separation from the middle of the frame, where the contact area is smaller.
Put some transparent scotch tape to prevent the glass from shattering.
Warm the glass for a minute to make adhesive soften.
Start the separation from the middle of the frame, where the contact area is smaller.
Step 9
- When you finished with the separation the glass, clean the frame from the old adhesive.
- Install the new touch screen and start to reassemble the device.
When you finished with the separation the glass, clean the frame from the old adhesive.
Install the new touch screen and start to reassemble the device.
Step 10
- That’s all.
That’s all.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
5 other people completed this guide.
Author
ZFix
Member since: 12/09/2013
187,195 Reputation
330 Guides authored
Badges:
35
+32 more badges
Team
Master Techs
Member of Master Techs
Community
310 Members
1,168 Guides authored
Addison Ramsey - Aug 8, 2017
Reply
Is the lcd adhesive just on the edges of the lcd or covering the entire thing?
