Difficulty
Moderate
Steps
14
Time Required
15 minutes
Sections
1
- Battery
- 14 steps
Flags
0
BackWatch
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Thoroughly clean the watch using electronic wipes.
- Be sure to get around the battery cover and remove as much dirt, dust, and/or debris to ensure an easy removal.
Thoroughly clean the watch using electronic wipes.
Be sure to get around the battery cover and remove as much dirt, dust, and/or debris to ensure an easy removal.
1024
Step 2
- Locate the spring pin under the band strap with the latch hole.
- Insert a push-pin into the hole.
- Push against the spring pin as needed until the band strap pops out.
- Remove the spring pin.
- Be sure to place the spring pin in a safe location. You will need it later for reassembling the watch.
Locate the spring pin under the band strap with the latch hole.
Insert a push-pin into the hole.
Push against the spring pin as needed until the band strap pops out.
Remove the spring pin.
Be sure to place the spring pin in a safe location. You will need it later for reassembling the watch.
Step 3
- Lay the watch clock face down on a dry, flat surface.
Lay the watch clock face down on a dry, flat surface.
Step 4
- Place a spudger into the small notch on the edge of the battery cover.
- Pry the battery cover, using as much force as necessary.
- How well you cleaned around the battery cover in Step 1 may determine how much force you will need to use.
- Remove the cover and place it to the side.
Place a spudger into the small notch on the edge of the battery cover.
Pry the battery cover, using as much force as necessary.
How well you cleaned around the battery cover in Step 1 may determine how much force you will need to use.
Remove the cover and place it to the side.
Step 5
- Remove the plastic piece and set it aside.
- You can do this step using either a spudger or your fingers.
Remove the plastic piece and set it aside.
You can do this step using either a spudger or your fingers.
Step 6
- Remove the battery from the watch.
- You can do this step using either a spudger or your fingers.
- Batteries are considered hazardous waste. Do not throw away the battery. Keep it until you are able to dispose of it properly. Depending on where you live, some stores like Best Buy will recycle batteries for you at no charge.
Remove the battery from the watch.
Batteries are considered hazardous waste. Do not throw away the battery. Keep it until you are able to dispose of it properly. Depending on where you live, some stores like Best Buy will recycle batteries for you at no charge.
Step 7
- Insert the new battery into the watch.
- Depending on the brand you buy, the battery needs to be an SR616SW or a 321.
Insert the new battery into the watch.
Depending on the brand you buy, the battery needs to be an SR616SW or a 321.
Step 8
- Insert the plastic piece back into the watch.
- The inner flap of the plastic piece should lay right on top of the battery and cover it completely.
Insert the plastic piece back into the watch.
The inner flap of the plastic piece should lay right on top of the battery and cover it completely.
Step 9
- Lay the battery cover back onto the watch.
- There is a very small notch under the cover that should line up with the crown of the watch.
Lay the battery cover back onto the watch.
There is a very small notch under the cover that should line up with the crown of the watch.
Step 10
- Press firmly on the battery cover, using both of your thumbs to snap it back in place.
Press firmly on the battery cover, using both of your thumbs to snap it back in place.
Step 11
- Re-insert the pin you removed into the hole of the smaller (lengthwise) folding segment.
Re-insert the pin you removed into the hole of the smaller (lengthwise) folding segment.
Step 12
- Align both ends of the watch, holding the segment with the spring pin adjacent to the hole.
Align both ends of the watch, holding the segment with the spring pin adjacent to the hole.
Step 13
- Use a spudger to press down on the spring pin, guiding it into the second hole.
- Release once connecting segments are in place.
Use a spudger to press down on the spring pin, guiding it into the second hole.
Release once connecting segments are in place.
Step 14
- Optional: Use your electronic wipes to remove any unwanted fingerprints.
- Place your wrist in the watch.
- Relatch to ensure you correctly reassembled the watch.
Optional: Use your electronic wipes to remove any unwanted fingerprints.
Place your wrist in the watch.
Relatch to ensure you correctly reassembled the watch.
Congratulations! You have replaced the battery from your Michael Kors Hartman Rose Gold watch. If you followed the step-by-step instructions, you should now have a fully reconstructed watch that is properly working. If it is not working properly, go back and carefully repeat the steps to ensure you completed everything correctly. Be sure to adjust the watch to display the correct time, and you will be ready to go.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 2 other contributors
Tyrell
Member since: 09/30/2021
268 Reputation
1 Guide authored
Badges:
6
+3 more badges
Team
University of North Texas, Team 2-13, Raign Fall 2021
Member of University of North Texas, Team 2-13, Raign Fall 2021
UNT-RAIGN-F21S2G13
2 Members
1 Guide authored
