Difficulty
Moderate
Steps
15
Time Required
25 minutes
Sections
1
- Upper Cover
- 15 steps
Flags
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackMFC-J4410DW
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Preparation
- Before beginning disassembly, turn off the printer and unplug the power cord.
- Open the front access door and remove any cards or cables present. Close the access door.
- Remove the paper tray.
- Remove the ink cartridges.
- You may wish to install the Protective Part to prevent the ink tubes from drying while the cartridges are removed.
- Open the printer cover using the finger holds on the sides.
- Unplug and remove any cords present under the cover.
- Remove the LAN port and EXT port caps (if present).
Before beginning disassembly, turn off the printer and unplug the power cord.
Open the front access door and remove any cards or cables present. Close the access door.
Remove the paper tray.
Remove the ink cartridges.
You may wish to install the Protective Part to prevent the ink tubes from drying while the cartridges are removed.
Open the printer cover using the finger holds on the sides.
Unplug and remove any cords present under the cover.
Remove the LAN port and EXT port caps (if present).
1024
Step 2
Removing the cover support
- While holding the cover with one hand, pull the hook on the back of the support damper, then remove the damper from the cover.
- Remove the damper from the support.
- Turn the support upright and pull it straight out of the printer.
While holding the cover with one hand, pull the hook on the back of the support damper, then remove the damper from the cover.
Remove the damper from the support.
Turn the support upright and pull it straight out of the printer.
Step 3
Removing the harness cover
- Use your finger or a spudger to unhook the two tabs on the right side of the harness cover by levering it up.
- Remove the harness cover. There are two tabs on the left side that you have to wiggle free, and one on the front.
Use your finger or a spudger to unhook the two tabs on the right side of the harness cover by levering it up.
Remove the harness cover. There are two tabs on the left side that you have to wiggle free, and one on the front.
Step 4
Removing the grounding screw
- Remove the 6 mm Phillips #2 screw from the grounding wire of the ADF motor harness.
- Torque: 0.40±0.10 N•m
- The Brother service manual lists torques for all screws, but proper torque should not be necessary.
Remove the 6 mm Phillips #2 screw from the grounding wire of the ADF motor harness.
Torque: 0.40±0.10 N•m
The Brother service manual lists torques for all screws, but proper torque should not be necessary.
Step 5
- In the proceeding steps, you will disconnect the following cables:
- CIS flat cable
- Scanner motor harness
- ADF motor harness
- Document detection/document scanning position sensor harness
In the proceeding steps, you will disconnect the following cables:
CIS flat cable
Scanner motor harness
ADF motor harness
Document detection/document scanning position sensor harness
Step 6
- Pull the CIS flat cable out of its socket.
- Pull all flat cables directly up out of their sockets, pulling on the cables themselves at the blue tabs.
Pull the CIS flat cable out of its socket.
Pull all flat cables directly up out of their sockets, pulling on the cables themselves at the blue tabs.
Step 7
- Pull the scanner motor harness out of its socket.
Pull the scanner motor harness out of its socket.
Step 8
- Pull the ADF motor harness out of its socket.
Pull the ADF motor harness out of its socket.
Step 9
- Pull the document detection/document scanning position sensor harness out of its sockets.
Pull the document detection/document scanning position sensor harness out of its sockets.
Step 10
Opening the scanner harness holder
- Insert a spudger between the scanner harness holder and frame to release the tab. There is a second tab on the opposite side.
- Lift the scanner harness holder out of its frame.
- Reassembly Note: Before reattaching the harness holder, it is advisable to reattach the cover support (Step 2) to minimize tension on the wiring harnesses.
Insert a spudger between the scanner harness holder and frame to release the tab. There is a second tab on the opposite side.
Lift the scanner harness holder out of its frame.
Reassembly Note: Before reattaching the harness holder, it is advisable to reattach the cover support (Step 2) to minimize tension on the wiring harnesses.
Step 11
Securing the scanner harness holder
- Push on the tab to secure the scanner harness holder to the scanner cover.
- De-route the document detection/document scanning position sensor harness and the ADF motor harness from the scanner harness holder.
- During reassembly, put a 20mm-thick pad (book, stack of paper) on the scanner glass, close the scanner cover, then route the document detection/document scanning position sensor harness and the ADF motor harness through the harness holder. This will ensure the proper harness tension to allow scanning of thick books.
Push on the tab to secure the scanner harness holder to the scanner cover.
De-route the document detection/document scanning position sensor harness and the ADF motor harness from the scanner harness holder.
During reassembly, put a 20mm-thick pad (book, stack of paper) on the scanner glass, close the scanner cover, then route the document detection/document scanning position sensor harness and the ADF motor harness through the harness holder. This will ensure the proper harness tension to allow scanning of thick books.
Step 12
Removing the scanner cover
- Using both hands, pull the scanner cover to the rear while holding it vertically, then lift it off of the printer.
Using both hands, pull the scanner cover to the rear while holding it vertically, then lift it off of the printer.
Step 13
Removing the upper cover
- Remove the six 12 mm Phillips #2 screws securing the upper cover to the printer.
- Torque: 0.70±0.10 N•m
- Pull off the upper cover.
- When reinstalling, ensure that the control panel wiring holder slides into its slot on the upper cover.
Remove the six 12 mm Phillips #2 screws securing the upper cover to the printer.
Torque: 0.70±0.10 N•m
Pull off the upper cover.
When reinstalling, ensure that the control panel wiring holder slides into its slot on the upper cover.
Step 14
Removing the ink absorber box wiring
- Remove the ink absorber full sensor from its socket.
- De-route the wiring from its harness.
Remove the ink absorber full sensor from its socket.
De-route the wiring from its harness.
Step 15
Unhooking the ink absorber
- Unclip the ink absorber from the harness by pulling it up and to the right.
Unclip the ink absorber from the harness by pulling it up and to the right.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 1 other contributor
Calion
Member since: 12/24/2010
2,284 Reputation
3 Guides authored
Badges:
20
+17 more badges
Team
Syler Solutions
Member of Syler Solutions
Business
1 Member
8 Guides authored
Patricia Verdera - Dec 11, 2019
Reply
Muchas gracias me encanta la dedicacion y lo claro que esta hecho el manual.
Ian Shannon - Mar 14, 2021
Reply
Calion,
Quite good instructions. However I needed to get to the power supply, and most of this was very useful, because there are 2 screws supporting the power supply you need to take out with the uper cover removed and the fronf left corner moulding removed. But step 14 and 15 are not necessary, and some of the cable disconnections are not needed.
On step 2 also showing the support damper (removed) with an arrow showing the hook on the back of the support damper would have saved lots of time as I had great difficulty with this step.
Thanks again
Ian
Calion - Mar 14, 2021
I can see how that would be helpful. Feel free to add it!