Difficulty

Moderate

Steps

8

Time Required

                          20 minutes

Sections

1

  • Sway Bar Link
  • 8 steps

Flags

0

  • BackMercedes W123

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

If, as you drive or rough roads, you hear a lot of rumbling or clunking from the rear of the car the first place to check is the sway bar links. It’s easy to diagnose, and almost as easy to replace. Do yours today; stop living with the noise!

What you need

Step 1

              Sway Bar Link
  • You will need to begin by jacking up the rear end of your car, and removing the rear wheels. If you need help with these, see the guides below:
  • Jacking technique guide.
  • Wheel removal technique guide

You will need to begin by jacking up the rear end of your car, and removing the rear wheels. If you need help with these, see the guides below:

Jacking technique guide.

Wheel removal technique guide

1024

Step 2

  • You can see here the sway bar link where it attaches to the sway bar. It’s hidden partially behind the brake shield. It’s tricky to take a good picture of…
  • The threaded portion of the link goes through a hole in the sway bar end and is held in place by a nut.

You can see here the sway bar link where it attaches to the sway bar. It’s hidden partially behind the brake shield. It’s tricky to take a good picture of…

The threaded portion of the link goes through a hole in the sway bar end and is held in place by a nut.

Step 3

  • At the bottom, it screws in to the hub assembly.

At the bottom, it screws in to the hub assembly.

Step 4

  • View this video to hear what a bad sway bar link sounds like when you move the sway bar around. If yours sounds like this is definitely time to replace it.

View this video to hear what a bad sway bar link sounds like when you move the sway bar around. If yours sounds like this is definitely time to replace it.

Step 5

  • Remove the nut from the top of the sway bar link using a 17 mm socket to turn off the nut while holding the inside of the sway bar link joint with an open end 17mm wrench.
  • Then use the open end 17mm wrench to loosen the bottom joint of the sway bar from the hub assembly.
  • You’ll then be able to remove the sway bar link for inspection. Save the nut and any washers as the new links do not come with replacements.

Remove the nut from the top of the sway bar link using a 17 mm socket to turn off the nut while holding the inside of the sway bar link joint with an open end 17mm wrench.

Then use the open end 17mm wrench to loosen the bottom joint of the sway bar from the hub assembly.

You’ll then be able to remove the sway bar link for inspection. Save the nut and any washers as the new links do not come with replacements.

Step 6

  • Pictured are example of the joints on the two sway bar links that were removed from this 1985 300D. Each one is split or even missing.
  • You can see how this exposes the joint to moisture, dust, and road debris; this quickly ruins the joint.

Pictured are example of the joints on the two sway bar links that were removed from this 1985 300D. Each one is split or even missing.

You can see how this exposes the joint to moisture, dust, and road debris; this quickly ruins the joint.

Step 7

  • Watch this video to see how loose the bottom joint on this sway bar link was. It was half of the culprit for the clunking. The other side was just as bad.

Watch this video to see how loose the bottom joint on this sway bar link was. It was half of the culprit for the clunking. The other side was just as bad.

Step 8

  • Install the new sway bar links by following these steps generally in reverse.
  • View this video to hear the difference with new links. Or, perhaps more accurately, not hear anything at all!

Install the new sway bar links by following these steps generally in reverse.

View this video to hear the difference with new links. Or, perhaps more accurately, not hear anything at all!

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      8 other people completed this guide.

Author

                                      with 1 other contributor 


                    Nicolas Siemsen

Member since: 12/06/2013

38,128 Reputation

                                      79 Guides authored                  



                       Badges:
                       30







                                                        +27 more badges

Team

                       Master Techs                        

                                                  Member of Master Techs 



                    Community                     


                                            310 Members                     


                                            1,168 Guides authored

Pat OBrien - Nov 19, 2014

Reply

Great photos and videos. Good job. Thanks.

Nicolas Siemsen - Nov 21, 2014

You’re welcome! This is definitely one of those repairs that are 1) easy and 2) provide a LOT of immediate tangible benefit. It’s super annoying driving around with bad sway bar links.

adelkheir - Oct 8, 2016

Reply

How to get it off the hub assembly in the first place ? do I have to remove the brake disks ? and how much do I need to torque them