Memorex Mi3X Minimove Back Panel Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 - 30 minutes

Sections

Back Panel
11 steps

Flags

BackMemorex Mi3X Minimove
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Back Panel

Remove the two plastic screw covers on the back of your Minimove by inserting the flat end of your plastic opening tool between the screw cover and the back panel and prying it out.
It may be helpful to pull the plastic covers out with your fingers once the top of the cover has been revealed by using the plastic opening tool.

Remove the two plastic screw covers on the back of your Minimove by inserting the flat end of your plastic opening tool between the screw cover and the back panel and prying it out.

It may be helpful to pull the plastic covers out with your fingers once the top of the cover has been revealed by using the plastic opening tool.

1024

Step 2

This step will require at least a 30 mm Phillips #1 screwdriver.
Use a Phillips #1 screwdriver to remove the two 12 mm screws.

This step will require at least a 30 mm Phillips #1 screwdriver.

Use a Phillips #1 screwdriver to remove the two 12 mm screws.

Step 3

The bottom panel screws and screw covers must be removed in order to access the back panel.
Remove the four grey screw covers by inserting the plastic opening tool underneath the screw covers and rotating around the circumference.
The adhesive on the screw covers should be sticky enough to put the covers back on when re-assembling the device.

The bottom panel screws and screw covers must be removed in order to access the back panel.

Remove the four grey screw covers by inserting the plastic opening tool underneath the screw covers and rotating around the circumference.

The adhesive on the screw covers should be sticky enough to put the covers back on when re-assembling the device.

Step 4

Remove the two 8 mm screws with a Phillips #1 screwdriver.
Remove the two 12 mm screws with a long Phillips #1 screwdriver.

Remove the two 8 mm screws with a Phillips #1 screwdriver.

Remove the two 12 mm screws with a long Phillips #1 screwdriver.

Step 5

To remove the back panel, use the plastic opening tool and gently work around the outline of the panel. The outline wraps around the sides and can be spotted at the top back of the device.

To remove the back panel, use the plastic opening tool and gently work around the outline of the panel. The outline wraps around the sides and can be spotted at the top back of the device.

Step 6

Be careful not to use too much force to remove the panel. The antenna wire is connected to the inside of the panel and may be damaged or ripped off if the panel is not gently removed.
After loosening the panel with the plastic opening tool, use moderate force to pry open the panel with your hands.
Carefully pull the panel off.

Be careful not to use too much force to remove the panel. The antenna wire is connected to the inside of the panel and may be damaged or ripped off if the panel is not gently removed.

After loosening the panel with the plastic opening tool, use moderate force to pry open the panel with your hands.

Carefully pull the panel off.

Step 7

Use a Phillips #1 screwdriver to detach the wire from the back panel by removing the 8 mm screw connecting the wire to the antenna.

Use a Phillips #1 screwdriver to detach the wire from the back panel by removing the 8 mm screw connecting the wire to the antenna.

Step 8

If desired, the antenna can now be removed by pulling inwards and horizontal to the panel bottom.

If desired, the antenna can now be removed by pulling inwards and horizontal to the panel bottom.

Step 9

Use the Phillips #1 screwdriver to remove the four 12 mm screws.
Remove the five 6 mm screws at the top with the same screwdriver.

Use the Phillips #1 screwdriver to remove the four 12 mm screws.

Remove the five 6 mm screws at the top with the same screwdriver.

Step 10

Use a Phillips #1 screwdriver and remove the two vertical 8 mm screws from the top.

Use a Phillips #1 screwdriver and remove the two vertical 8 mm screws from the top.

Step 11

Pry open the inner back panel by inserting the plastic opening tool in the crack at the top corner.
Use moderate force to pry it open and take the cover off.

Pry open the inner back panel by inserting the plastic opening tool in the crack at the top corner.

Use moderate force to pry it open and take the cover off.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 8 other contributors

                    Michael Johnson

Member since: 01/31/2014

237 Reputation

                                      2 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team 2-9, Amido Winter 2014                        

                                                  Member of Cal Poly, Team 2-9, Amido Winter 2014 



                    CPSU-AMIDO-W14S2G9                     


                                            5 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team