Difficulty

Difficult

Steps

10

Time Required

                          4 hours

Sections

1

  • W10219156 Hub and Seal Kit
  • 10 steps

Flags

2

In Progress

This guide is a work in progress. Reload periodically to see the latest changes!

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackRéparation Maytag Atlantis MAV9750AWW

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

The Atlantis MAV9750AWW is very good machine and it worth it to fix it. This kit is approximativly 160$ CAD.

Good tutoriel is this generic video:

https://youtu.be/6qSiuTtrPOc

What you need

Step 1

              W10219156 Hub and Seal Kit

https://www.youtube.com/watch?v=6qSiuTtr…

1024

Step 2

  • remove agitator, and thub

remove agitator, and thub

Step 3

  • remove thub

remove thub

Step 4

  • remove transmission out of the washer

remove transmission out of the washer

Step 5

  • remove hub by unscrew it. use two pipe wrech or cut it.

remove hub by unscrew it. use two pipe wrech or cut it.

Step 6

  • assemble new part on the transmission. The 4 srew

assemble new part on the transmission. The 4 srew

Step 7

  • The original screw was 4 x 1" M8 - 1.5 self treaded, screw was damage and rusty, New from Maytag are 10$ each and are not so good. I change it for stainless stel screw. Could not find M8 on stainelss stel I use a equivalent 5/16-18.

The original screw was 4 x 1" M8 - 1.5 self treaded, screw was damage and rusty, New from Maytag are 10$ each and are not so good. I change it for stainless stel screw. Could not find M8 on stainelss stel I use a equivalent 5/16-18.

Step 8

  • Use tap to tread the hub. Don’t forget to remplace the nylon washer and I add a stainless stel washer also.

Use tap to tread the hub. Don’t forget to remplace the nylon washer and I add a stainless stel washer also.

Step 9

  • remove corrosion if required, check electrical connection. (I paint the botom and re-do ground connection.)

remove corrosion if required, check electrical connection. (I paint the botom and re-do ground connection.)

Step 10

  • re-assemble thub and cuve

re-assemble thub and cuve

Folow generic video instruction: https://www.youtube.com/watch?v=6qSiuTtr…

If you dont have the special tool to remove the hub:

Remove the thub, take the whole transmission out of the washer machine to have some room to work.

Take two pipe wrech one on the hub, the other on the bottom of the transmission and unscrew the hub, work hard. On my side, I was not able to unscrew it, I cut the hub wit a grinder it was the fastest way. becarful to not cut the shaft. Finish the work with a big shissel and hammer.

Reasembling is easy.

Pour réassembler votre appareil, suivez les instructions dans l’ordre inverse.

Cancel: I did not complete this guide.

Attached Documents

  • Microsoft Word - Doc7.docx
  • PDF - 169.37 kb
  • View

Microsoft Word - Doc7.docx

PDF - 169.37 kb

Author

                                      with 1 other contributor 


                    franck_gab

Member since: 04/03/2020

181 Reputation

                                      1 Guide authored                  



                       Badges:
                       1