Maylong Mn 1000P Keyboard Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          2 minutes

Sections

Bottom Cover
5 steps
Battery
1 step
Screen
9 steps
Motherboard
7 steps
Keyboard
2 steps

Flags

Inconsistent Images

Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.

BackMaylong MN-1000P
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Bottom Cover

Place the netbook top down, with the opening of the netbook facing you.

Place the netbook top down, with the opening of the netbook facing you.

1024

Step 2

Remove the six 6mm Phillips #00 screws from the netbook.

Remove the six 6mm Phillips #00 screws from the netbook.

Step 3

Remove the sticker in the middle of the netbook.
Remove the middle 6mm Phillips #00 screw.

Remove the sticker in the middle of the netbook.

Remove the middle 6mm Phillips #00 screw.

Step 4

Using two plastic opening tools, pry off the bottom of the netbook by going around the edges.

Using two plastic opening tools, pry off the bottom of the netbook by going around the edges.

Step 5

Remove the bottom of the netbook by lifting the corners.

Remove the bottom of the netbook by lifting the corners.

Step 6

              Battery

Pinch the red and black wires connected to the section closest to the small white connector, and pull to remove them from the motherboard.

Pinch the red and black wires connected to the section closest to the small white connector, and pull to remove them from the motherboard.

Step 7

              Screen

Remove the six 6mm Phillips #00 screws from both sides of the netbook.

Remove the six 6mm Phillips #00 screws from both sides of the netbook.

Step 8

Pull the top of the computer and the back side of the computer away from each other until they are detached.
Flip the entire computer over so you can see both the screen and keyboard.

Pull the top of the computer and the back side of the computer away from each other until they are detached.

Flip the entire computer over so you can see both the screen and keyboard.

Step 9

Remove all the black circular pads from around the screen.
Remove all 6mm Phillips #00 screws from around the screen bezel.

Remove all the black circular pads from around the screen.

Remove all 6mm Phillips #00 screws from around the screen bezel.

Step 10

Using a plastic opening tool, pry off the screen bezel.
After detaching the screen bezel, pull up on the bezel near the hinge area.

Using a plastic opening tool, pry off the screen bezel.

After detaching the screen bezel, pull up on the bezel near the hinge area.

Step 11

Use tweezers to gently pull on the black and white wires at the top of the netbook until the white connector detaches.

Use tweezers to gently pull on the black and white wires at the top of the netbook until the white connector detaches.

Step 12

Use your fingers to pull on the green, red, black, and white intertwined wires at the bottom of the netbook until the white connector detaches.

Use your fingers to pull on the green, red, black, and white intertwined wires at the bottom of the netbook until the white connector detaches.

Step 13

Detach the wide yellow ribbon cable connected to the screen from the computer.

Detach the wide yellow ribbon cable connected to the screen from the computer.

Step 14

Flip the computer over.
Disconnect the red, green, black, and white intertwined wires from the connector to the motherboard.

Flip the computer over.

Disconnect the red, green, black, and white intertwined wires from the connector to the motherboard.

Step 15

Remove the black tape holding down the red, green, black, and white intertwined wires.
Remove the screen.

Remove the black tape holding down the red, green, black, and white intertwined wires.

Remove the screen.

Step 16

              Motherboard

Remove the six 6mm Phillips #00 screws from the motherboard.

Remove the six 6mm Phillips #00 screws from the motherboard.

Step 17

Remove the two 6mm silver screws from the small circuit board connected to the motherboard by the red and black wires.

Remove the two 6mm silver screws from the small circuit board connected to the motherboard by the red and black wires.

Step 18

Remove the two small black speakers on the corners connected to the motherboard by the black and red wires.

Remove the two small black speakers on the corners connected to the motherboard by the black and red wires.

Step 19

Disconnect the black connectors from the motherboard by pulling on the white ribbon cable.

Disconnect the black connectors from the motherboard by pulling on the white ribbon cable.

Step 20

Remove the black covered wire connected to the motherboard by pulling the white ribbon cable away from the motherboard.

Remove the black covered wire connected to the motherboard by pulling the white ribbon cable away from the motherboard.

Step 21

Using a spudger, remove the gold cylinder out of the indent at the bottom of the computer.

Using a spudger, remove the gold cylinder out of the indent at the bottom of the computer.

Step 22

Lift the motherboard up.
Remove the motherboard by detaching the clear tape from underneath the motherboard.

Lift the motherboard up.

Remove the motherboard by detaching the clear tape from underneath the motherboard.

Step 23

              Keyboard

Hold the keyboard panel with the back facing you.
Using your thumbs, push on the silver squares.

Hold the keyboard panel with the back facing you.

Using your thumbs, push on the silver squares.

Step 24

Flip the netbook over so the keyboard is facing upwards.
Insert a spudger between the keyboard and the top of the plate.
Lift the keyboard up and away from the mouse pad to remove.

Flip the netbook over so the keyboard is facing upwards.

Insert a spudger between the keyboard and the top of the plate.

Lift the keyboard up and away from the mouse pad to remove.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    katelyn buckman

Member since: 01/13/2020

553 Reputation

                                      5 Guides authored                  



                       Badges:
                       3

Team

                       Eastern Washington University, Team S1-G3, Carnegie Winter 2020                        

                                                  Member of Eastern Washington University, Team S1-G3, Carnegie Winter 2020 



                    EWU-CARNEGIE-W20S1G3                     


                                            3 Members                     


                                            5 Guides authored

Inconsistent Images#

Introduction#

What you need#

Team#

Inconsistent Images

Introduction

What you need

Team