Difficulty
Moderate
Steps
14
Time Required
10 - 30 minutes
Sections
3
- Battery
- 5 steps
- Motherboard
- 8 steps
- Camera
- 1 step
Flags
0
BackMatsunichi M97 9 inch
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Open the micro SD cover located on the back of the device.
Open the micro SD cover located on the back of the device.
1024
Step 2
- Using the Phillips #00 screwdriver, remove the two 4mm screws next to the micro SD port.
Using the Phillips #00 screwdriver, remove the two 4mm screws next to the micro SD port.
Step 3
- Use the iFixit opening tool to pry off the back cover of the device.
- The volume buttons and the lock switch will come loose when the back comes off.
Use the iFixit opening tool to pry off the back cover of the device.
The volume buttons and the lock switch will come loose when the back comes off.
Step 4
- Use a pair of tweezers to disconnect the battery from the motherboard.
Use a pair of tweezers to disconnect the battery from the motherboard.
Step 5
- Carefully unstick the battery from the frame using the spudger.
- Do not bend or puncture the battery during removal.
Carefully unstick the battery from the frame using the spudger.
Do not bend or puncture the battery during removal.
Step 6
Motherboard
- Remove the six 2mm screws that hold the motherboard onto the case using the Phillips #00 screwdriver.
- Use the same screwdriver to remove the single 4mm screw.
Remove the six 2mm screws that hold the motherboard onto the case using the Phillips #00 screwdriver.
Use the same screwdriver to remove the single 4mm screw.
Step 7
- Gently pull the display ribbon cable to unplug it from the motherboard.
Gently pull the display ribbon cable to unplug it from the motherboard.
Step 8
- Use a spudger or an iFixit opening tool to lift the locking mechanism holding the camera ribbon cable.
Use a spudger or an iFixit opening tool to lift the locking mechanism holding the camera ribbon cable.
Step 9
- Lift up on the wifi antenna cable to unsnap it from the motherboard.
- Then unhook the cable from the holding bracket.
Lift up on the wifi antenna cable to unsnap it from the motherboard.
Then unhook the cable from the holding bracket.
Step 10
- Use the spudger or iFixit opening tool to lift up on the locking mechanism for the digitizer ribbon cable.
- Pull the cable from its connection.
Use the spudger or iFixit opening tool to lift up on the locking mechanism for the digitizer ribbon cable.
Pull the cable from its connection.
Step 11
- Use the Phillips #00 screwdriver to remove the four 4mm screws that hold the speakers in place.
Use the Phillips #00 screwdriver to remove the four 4mm screws that hold the speakers in place.
Step 12
- Pull the vibration motor out of its housing.
Pull the vibration motor out of its housing.
Step 13
- Lift the motherboard off the frame.
Lift the motherboard off the frame.
Step 14
Camera
- Remove the camera from the device.
Remove the camera from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Violet Ruff
Member since: 01/16/2020
93 Reputation
1 Guide authored
Badges:
3
Team
Embry-Riddle Aeronautical University, Team S7-G8, Rauch Spring 2020
Member of Embry-Riddle Aeronautical University, Team S7-G8, Rauch Spring 2020
ERAU-RAUCH-S20S7G8
4 Members
5 Guides authored