Difficulty
Moderate
Steps
20
Time Required
1 - 2 hours
Sections
5
- Back Plate
- 2 steps
- Lithium Battery
- 2 steps
- Motherboard
- 5 steps
- LED Screen
- 7 steps
- Watch Face
- 4 steps
Flags
3
Markup Mishap
This guide needs better markups. Help out by correcting or making some markup annotations.
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
Better Introduction
Improve this guide by completing or revising its introduction.
BackMartian Victory
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Plate
- Unscrew the four 3.4 mm flat head screws
Unscrew the four 3.4 mm flat head screws
1024
Step 2
- Carefully lift the back plate off the watch. You will notice a lithium battery and rubber gasket attached to the back plate.
Carefully lift the back plate off the watch. You will notice a lithium battery and rubber gasket attached to the back plate.
Step 3
Lithium Battery
- If not replacing lithium battery, skip down two steps.
- Using the plastic removal tool, pry the battery from the backing plate. The battery is simply attached with glue.
If not replacing lithium battery, skip down two steps.
Using the plastic removal tool, pry the battery from the backing plate. The battery is simply attached with glue.
Step 4
- Desolder the battery connections from the motherboard. Learn how to solder components here!
Desolder the battery connections from the motherboard. Learn how to solder components here!
Step 5
Motherboard
- Use PH00 screw driver to remove two 2.4mm Phillips head screws.
Use PH00 screw driver to remove two 2.4mm Phillips head screws.
Step 6
- Use a spudger or tweezers to remove a white sticker that covers a Phillips head screw.
Use a spudger or tweezers to remove a white sticker that covers a Phillips head screw.
Step 7
- Use PH00 screwdriver to remove 5.2mm Phillips head screw
Use PH00 screwdriver to remove 5.2mm Phillips head screw
Step 8
- Use ESD safe tweezers to remove the gold ribbon cable.
- This will expose a second 5.2mm Phillips head screw that can be removed with a PH00 screwdriver.
Use ESD safe tweezers to remove the gold ribbon cable.
This will expose a second 5.2mm Phillips head screw that can be removed with a PH00 screwdriver.
Step 9
- Use a spudger to gently pry on the motherboard towards the top of the watch, being towards the 12 o’clock position to loosen the motherboard.
- You can now access the parts and pieces on the bottom of, and below the motherboard.
Use a spudger to gently pry on the motherboard towards the top of the watch, being towards the 12 o’clock position to loosen the motherboard.
You can now access the parts and pieces on the bottom of, and below the motherboard.
Step 10
LED Screen
- Locate the ribbon connection, and use remove the clips holding the strip on each side using needle tool.
Locate the ribbon connection, and use remove the clips holding the strip on each side using needle tool.
Step 11
- With a pair of tweezers, carefully remove the ribbon strip connection.
With a pair of tweezers, carefully remove the ribbon strip connection.
Step 12
- Remove the screw driver holding the LED screen and Speaker in place.
Remove the screw driver holding the LED screen and Speaker in place.
Step 13
- Insert a small flat screw driver under the speaker in order to remove it.
Insert a small flat screw driver under the speaker in order to remove it.
Step 14
- Using tweezers, remove the speaker and move off to the side.
Using tweezers, remove the speaker and move off to the side.
Step 15
- Place a small flat head screwdriver under the LED screen, and carefully push it out of it’s socket.
Place a small flat head screwdriver under the LED screen, and carefully push it out of it’s socket.
Step 16
- Remove final connection to accelerometer. The LED screen is now separated from the device.
Remove final connection to accelerometer. The LED screen is now separated from the device.
Step 17
Watch Face
- Grab the motherboard with tweezers and remove from watch cavity.
Grab the motherboard with tweezers and remove from watch cavity.
Step 18
- Stabilize watch with the metal prove. Place tweezers around crown and pull outward, so that the crown can be removed.
Stabilize watch with the metal prove. Place tweezers around crown and pull outward, so that the crown can be removed.
Step 19
- Insert the spudger under plastic panel cover in order to access watch face.
Insert the spudger under plastic panel cover in order to access watch face.
Step 20
- Insert a spudger under the black watch face. Gently push up, so that it can be raised out of the watch.
- Use tweezers or pin tool in order to remove from watch.
Insert a spudger under the black watch face. Gently push up, so that it can be raised out of the watch.
Use tweezers or pin tool in order to remove from watch.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Robert Sanchez
Member since: 10/31/2016
201 Reputation
2 Guides authored
Badges:
4
+1 more badge
Team
IUPUI, Team 3-3, Baechle Fall 2016
Member of IUPUI, Team 3-3, Baechle Fall 2016
IUPUI-BAECHLE-F16S3G3
4 Members
8 Guides authored