Difficulty

Difficult

Steps

6

Time Required

                          15 minutes

Sections

1

  • Power Cord
  • 6 steps

Flags

0

  • BackNutriBullet rx

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Power Cord
  • Before beginning, make sure the device is unplugged.
  • With a Phillips head #2 screwdriver, begin unscrewing the four 10mm screws located on the bottom of the power base.

Before beginning, make sure the device is unplugged.

With a Phillips head #2 screwdriver, begin unscrewing the four 10mm screws located on the bottom of the power base.

1024

Step 2

  • Once the screws are removed, pull the plastic base up gently.
  • Once the plastic base is removed, there is a fan located in the center of the powerbase. Make sure the cord does not get caught or frayed by the fan.

Once the screws are removed, pull the plastic base up gently.

Once the plastic base is removed, there is a fan located in the center of the powerbase. Make sure the cord does not get caught or frayed by the fan.

Step 3

  • Gently lift the power cord from its side slot and place it to the side.

Gently lift the power cord from its side slot and place it to the side.

Step 4

  • With the Phillips head #2 screwdriver, remove the two 10mm screws that secure the white bracket.
  • The white safety bracket holds the cord down. After removing it, the cord will be free.

With the Phillips head #2 screwdriver, remove the two 10mm screws that secure the white bracket.

The white safety bracket holds the cord down. After removing it, the cord will be free.

Step 5

  • After removing the gray base and silver casing, the wires will now be free and you will have easy access to them.
  • Gently pull out the two plastic covers at the end of the wires.

After removing the gray base and silver casing, the wires will now be free and you will have easy access to them.

Gently pull out the two plastic covers at the end of the wires.

Step 6

  • Use tape or clamps to hold the wires together for an easy soldering experience.
  • Using a soldering iron, solder your new wire to the red wire.

Use tape or clamps to hold the wires together for an easy soldering experience.

Using a soldering iron, solder your new wire to the red wire.

Since this guide replacement requires cutting wires, if you want to reassemble this device, you must first re-solder new wires before following the steps backwards to reassemble the device.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 13 other contributors 


                    Geary Yu

Member since: 01/22/2015

1,190 Reputation

                                      3 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       Cal Poly, Team 19-8, Maness Winter 2015                        

                                                  Member of Cal Poly, Team 19-8, Maness Winter 2015 



                    CPSU-MANESS-W15S19G8                     


                                            4 Members                     


                                            7 Guides authored

florentinokarenjoy24 - Jan 6, 2017

Reply

where am I going to be the magic bullet repair

Or

there a service center here in the philippines?

Thank u.

there a service center here in the philippines

Michael Lee - Mar 12, 2018

Reply

Is there a service centre in Singapore?

I just bought the gadget in Melbourne (from Harvey Norman Nunawarding) last week. We used it yesterday but after one round of spinning, gadget went dead.

What could go round and to fix it at home?

Sovelita Tenerife - Feb 13, 2019

Reply

Can I plug the Magic Bullet in 220v?

victoria hatton - Oct 1, 2019

Reply

Where can I get a replacement cable from?