Difficulty

Moderate

Steps

11

Time Required

                          15 - 20 minutes

Sections

2

  • Base Gear
  • 1 step
  • Casing
  • 10 steps

Flags

0

  • BackMagic Bullet MB1001B

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Base Gear
  • Use pliers to grip the gear inside of the top of the device.
  • You may have to remove a sticker that is covering the slit at the center of the bottom before completing the next step.
  • Insert a flathead screwdriver into the slit at the bottom of the device while still holding the pliers in place gripped on the gear.
  • Lay the device on its side. Holding the screwdriver stationary to hold the bottom side in place, use the pliers to unscrew the gear by turning the pliers CLOCKWISE.

Use pliers to grip the gear inside of the top of the device.

You may have to remove a sticker that is covering the slit at the center of the bottom before completing the next step.

Insert a flathead screwdriver into the slit at the bottom of the device while still holding the pliers in place gripped on the gear.

Lay the device on its side. Holding the screwdriver stationary to hold the bottom side in place, use the pliers to unscrew the gear by turning the pliers CLOCKWISE.

1024

Step 2

              Casing
  • Remove the four rubber pegs from the feet on the base of the Magic Bullet using the spudger.

Remove the four rubber pegs from the feet on the base of the Magic Bullet using the spudger.

Step 3

  • Remove the four 14.0 mm Phillips head screws in the feet of the base of the Magic Bullet using the Phillips #1 screwdriver.

Remove the four 14.0 mm Phillips head screws in the feet of the base of the Magic Bullet using the Phillips #1 screwdriver.

Step 4

  • Remove the black base plate.

Remove the black base plate.

Step 5

  • Remove the two 13.0 mm Phillips head screws from the white plastic cable guide using a Phillips #1 screwdriver.

Remove the two 13.0 mm Phillips head screws from the white plastic cable guide using a Phillips #1 screwdriver.

Step 6

  • Remove the white plastic cable guide.

Remove the white plastic cable guide.

Step 7

  • Remove the three 11.0 mm Phillips head screws surrounding the white fan blade on the base using the Phillips #1 screwdriver.

Remove the three 11.0 mm Phillips head screws surrounding the white fan blade on the base using the Phillips #1 screwdriver.

Step 8

  • Remove the black base.

Remove the black base.

Step 9

  • Remove the three white rubber spacers with the spudger.

Remove the three white rubber spacers with the spudger.

Step 10

  • Remove the three 11.0 mm Phillips head screws using the Phillips #1 screwdriver.

Remove the three 11.0 mm Phillips head screws using the Phillips #1 screwdriver.

Step 11

  • Remove the motor.

Remove the motor.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 5 other contributors 


                    Kelly McGartland

Member since: 10/06/2015

539 Reputation

                                      2 Guides authored                  



                       Badges:
                       14







                                                        +11 more badges

Team

                       Cal Poly, Team 12-13, Maness Fall 2015                        

                                                  Member of Cal Poly, Team 12-13, Maness Fall 2015 



                    CPSU-MANESS-F15S12G13                     


                                            4 Members                     


                                            8 Guides authored