Featured
Featured Guide
Difficulty
Easy
Steps
9
Time Required
10 minutes
Sections
4
- Rear and Side Case
- 4 steps
- RS-DP-LS Switch
- 1 step
- Circuit Board
- 2 steps
- Directional Pad
- 2 steps
Flags
2
Featured Student Guide
This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
BackMad Catz Street Fighter IV FightPad
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Rear and Side Case
- Use tweezers to completely remove the sticker from the rear of controller.
Use tweezers to completely remove the sticker from the rear of controller.
1024
Step 2
- Find the seven 8.3 mm Phillips screws on the rear of the controller and remove them.
Find the seven 8.3 mm Phillips screws on the rear of the controller and remove them.
Step 3
- Use a plastic opening tool to separate the rear and front casing by inserting it in-between the two cases.
- Use the plastic opening tool to pry the two cases apart.
Use a plastic opening tool to separate the rear and front casing by inserting it in-between the two cases.
Use the plastic opening tool to pry the two cases apart.
Step 4
- Remove the two rubber side grips.
Remove the two rubber side grips.
Step 5
RS-DP-LS Switch
- Locate RS-DP-LS switch.
- Pull upwards on the switch to remove it.
Locate RS-DP-LS switch.
Pull upwards on the switch to remove it.
Step 6
Circuit Board
- Locate the four 8.3 mm Phillips screws on the circuit board and remove them.
Locate the four 8.3 mm Phillips screws on the circuit board and remove them.
Step 7
- Hold the controller cable at the area just before it meets the controller and slowly lift upwards to slide it out of its plastic slot and remove the circuit board.
- Be careful with the wires connected to the circuit board itself as they are thin and delicate.
- When reassembling the controller, make sure that the bottom plastic piece is fully inserted into its slot before replacing the circuit board.
Hold the controller cable at the area just before it meets the controller and slowly lift upwards to slide it out of its plastic slot and remove the circuit board.
Be careful with the wires connected to the circuit board itself as they are thin and delicate.
When reassembling the controller, make sure that the bottom plastic piece is fully inserted into its slot before replacing the circuit board.
Step 8
Directional Pad
- Use tweezers to remove the rubber part of the directional pad.
Use tweezers to remove the rubber part of the directional pad.
Step 9
- Insert a new directional pad over the original directional pad’s location.
Insert a new directional pad over the original directional pad’s location.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 6 other contributors
Jefferson
Member since: 09/26/2012
78 Reputation
1 Guide authored
Badges:
7
+4 more badges
Team
Cal Poly, Team 1-7, Propen Fall 2012
Member of Cal Poly, Team 1-7, Propen Fall 2012
CPSU-PROPEN-F12S1G7
4 Members
14 Guides authored
auredo1988 - Oct 8, 2016
Reply
mi spiegate l’utilita di questa guida?vendere forse le pinzette e tutte le altre stronzatine che servono per riparare il fightpad?quando invece il pezzo più importante cioè il gommino non lo vendete….fate pena
Eric Devlin - Oct 18, 2016
Reply
Hi I don’t speak Italian but I think you are asking “what is the purpose of this guide?”. We made these as a project for university because I wanted to resolder a wire in this controller that came undone. For good measure we made a guide for each individual part although the real purpose of these guides was for the full disassembly and re soldering.
