Difficulty

Easy

Steps

6

Time Required

                          15 minutes

Sections

2

  • Outer Casing
  • 3 steps
  • Five Way Toggle Switch
  • 3 steps

Flags

0

  • BackMad Catz Rock Band 4 Wireless Fender

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Be sure to remove the batteries before beginning the replacement.

What you need

Step 1

              Outer Casing
  • Flip the guitar over so it is back side up. The battery compartment should be facing up.
  • Use a size J1 head screwdriver to remove the ten 5 mm short screws.
  • Use a J1 screwdriver to remove the four 5 mm long screws on the back of the device.

Flip the guitar over so it is back side up. The battery compartment should be facing up.

Use a size J1 head screwdriver to remove the ten 5 mm short screws.

Use a J1 screwdriver to remove the four 5 mm long screws on the back of the device.

1024

Step 2

  • Turn the device over so the front of the guitar is facing you.
  • Using a size J1 philips head screwdriver, remove the eleven 5 mm silver screws (circled in red) around the white panel.

Turn the device over so the front of the guitar is facing you.

Using a size J1 philips head screwdriver, remove the eleven 5 mm silver screws (circled in red) around the white panel.

Step 3

  • Gently lift the white panel and twist 90 degrees clockwise.
  • Using a size J1 head screwdriver, remove the two 5 mm black screws from underneath the white panel. You should now be able to pull the guitar apart.

Gently lift the white panel and twist 90 degrees clockwise.

Using a size J1 head screwdriver, remove the two 5 mm black screws from underneath the white panel. You should now be able to pull the guitar apart.

Step 4

              Five Way Toggle Switch
  • Look for the toggle switch component on the inside of the guitar. The component rests in a black, circular holder that is positioned perpendicular relative to the inside of the front of the guitar.
  • Unscrew the two black, vertical, 5 mm philips head screws holding the part in place using a size J1 screwdriver.

Look for the toggle switch component on the inside of the guitar. The component rests in a black, circular holder that is positioned perpendicular relative to the inside of the front of the guitar.

Unscrew the two black, vertical, 5 mm philips head screws holding the part in place using a size J1 screwdriver.

Step 5

  • Pull the entire component out in a vertical motion.

Pull the entire component out in a vertical motion.

Step 6

  • Follow the wires from the component to the main circuit board. Unplug the toggle switch component from the main board.
  • Plug in your replacement toggle switch hardware.

Follow the wires from the component to the main circuit board. Unplug the toggle switch component from the main board.

Plug in your replacement toggle switch hardware.

To reassemble your device, follow these instructions in reverse orde

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Hollynn Ricker

Member since: 09/28/2016

451 Reputation

                                      2 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       USF Tampa, Team 1-1, Cagle Fall 2016                        

                                                  Member of USF Tampa, Team 1-1, Cagle Fall 2016 



                    USFT-CAGLE-F16S1G1                     


                                            4 Members                     


                                            6 Guides authored