Difficulty

Difficult

Steps

30

Time Required

Suggest a time??

Sections

8

  • Lower Case
  • 2 steps
  • Battery
  • 1 step
  • Rear Vent
  • 3 steps
  • Display
  • 8 steps
  • Front Display Bezel
  • 5 steps
  • Clutch Cover
  • 3 steps
  • LCD
  • 4 steps
  • Display Data/Camera Cable
  • 4 steps

Flags

0

  • BackMacBook Unibody A1342

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Lower Case
  • Remove the eight 4 mm Phillips screws securing the lower case to the MacBook.

Remove the eight 4 mm Phillips screws securing the lower case to the MacBook.

1024

Step 2

  • The lower case is constructed of rubber-coated aluminum. Do not excessively bend the aluminum during removal, as any permanent deformation will cause tolerance issues after reassembly.
  • Slightly lift the lower case near the vent opening.
  • Continue running your fingers between the lower and upper cases until the upper case pops off its retaining clips.
  • The location of these three clips is shown in the third picture.

The lower case is constructed of rubber-coated aluminum. Do not excessively bend the aluminum during removal, as any permanent deformation will cause tolerance issues after reassembly.

Slightly lift the lower case near the vent opening.

Continue running your fingers between the lower and upper cases until the upper case pops off its retaining clips.

The location of these three clips is shown in the third picture.

Step 3

              Battery
  • For precautionary purposes, we advise that you disconnect the battery connector from the logic board to avoid any electrical discharge. This step is optional and is not required.
  • Use the flat end of a spudger to lift the battery connector up out of its socket on the logic board.
  • It may be easier to use your fingernails to lift up on both sides of the connector.

For precautionary purposes, we advise that you disconnect the battery connector from the logic board to avoid any electrical discharge. This step is optional and is not required.

Use the flat end of a spudger to lift the battery connector up out of its socket on the logic board.

It may be easier to use your fingernails to lift up on both sides of the connector.

Step 4

              Rear Vent
  • Remove the following screws from the optical drive side of the rear vent:
  • Two 10 mm T8 Torx
  • Two 5.2 mm Phillips

Remove the following screws from the optical drive side of the rear vent:

Two 10 mm T8 Torx

Two 5.2 mm Phillips

Step 5

  • Remove the following screws from the port side of rear vent:
  • Two 10 mm T8 Torx
  • Two 5.2 mm Phillips

Remove the following screws from the port side of rear vent:

Step 6

  • Carefully lift the rear vent out of the upper case.

Carefully lift the rear vent out of the upper case.

Step 7

              Display
  • Remove the single 3 mm Phillips screw securing the AirPort/Bluetooth antenna ground strap to the rear speaker.

Remove the single 3 mm Phillips screw securing the AirPort/Bluetooth antenna ground strap to the rear speaker.

Step 8

  • Use the tip of a spudger to pry the AirPort and Bluetooth antenna connectors (3 total) up off the AirPort/Bluetooth card.
  • De-route the long antenna from its channel in the rear speaker housing.

Use the tip of a spudger to pry the AirPort and Bluetooth antenna connectors (3 total) up off the AirPort/Bluetooth card.

De-route the long antenna from its channel in the rear speaker housing.

Step 9

  • Grab the plastic pull tab secured to the display data cable lock and rotate it toward the DC-In side of the computer.
  • There is also a thin metal lock clip under the plastic tab that has to be released ( Use the tip of a spudger ) before you can disconnect the display data cable.

Grab the plastic pull tab secured to the display data cable lock and rotate it toward the DC-In side of the computer.

There is also a thin metal lock clip under the plastic tab that has to be released ( Use the tip of a spudger ) before you can disconnect the display data cable.

Step 10

  • Gently pull the display data cable connector away from its socket on the logic board.
  • Pull the socket parallel to the face of the logic board.
  • The display data cable socket is made of very thin metal and is easily bent. Be sure to pull the connector straight away from its socket.

Gently pull the display data cable connector away from its socket on the logic board.

Pull the socket parallel to the face of the logic board.

The display data cable socket is made of very thin metal and is easily bent. Be sure to pull the connector straight away from its socket.

Step 11

  • Open your MacBook so the display is perpendicular to the upper case.
  • Place your opened MacBook on a table as pictured.
  • While holding the display and upper case together with your left hand, remove the remaining 7.8 mm with lock washer T8 Torx screw from the lower display bracket.

Open your MacBook so the display is perpendicular to the upper case.

Place your opened MacBook on a table as pictured.

While holding the display and upper case together with your left hand, remove the remaining 7.8 mm with lock washer T8 Torx screw from the lower display bracket.

Step 12

  • Be sure to hold the display and upper case together with your left hand. Failure to do so may cause the freed display/upper case to fall, potentially damaging each component.
  • Remove the last remaining T8 Torx screw securing the display to the upper case.

Be sure to hold the display and upper case together with your left hand. Failure to do so may cause the freed display/upper case to fall, potentially damaging each component.

Remove the last remaining T8 Torx screw securing the display to the upper case.

Step 13

  • Grab the upper case with your right hand and rotate it slightly toward the top of the display so the upper display bracket clears the edge of the upper case.
  • The display data cable may cause the upper display bracket to get caught on the upper case. It may be helpful to slightly rotate the upper case away from the display for more clearance.
  • Rotate the display slightly away from the upper case.

Grab the upper case with your right hand and rotate it slightly toward the top of the display so the upper display bracket clears the edge of the upper case.

The display data cable may cause the upper display bracket to get caught on the upper case. It may be helpful to slightly rotate the upper case away from the display for more clearance.

Rotate the display slightly away from the upper case.

Step 14

  • Lift the display up and away from the upper case, minding any brackets or cables that may get caught.

Lift the display up and away from the upper case, minding any brackets or cables that may get caught.

Step 15

              Front Display Bezel
  • Insert the flat end of a spudger between the thin rubber strip surrounding the front display bezel and the rear display bezel.
  • Do not try to insert the spudger between the thin rubber strip and the plastic face of the front display bezel.
  • Use the flat end of your spudger to carefully pry the front display bezel away from the adhesive securing it to the rear display bezel.
  • Do not pry against the fragile glass LCD panel. Also, do not excessively bend the plastic as it may permanently deform.
  • Continue prying until the front display bezel is free along the right side of the display and behind the right clutch hinge.

Insert the flat end of a spudger between the thin rubber strip surrounding the front display bezel and the rear display bezel.

Do not try to insert the spudger between the thin rubber strip and the plastic face of the front display bezel.

Use the flat end of your spudger to carefully pry the front display bezel away from the adhesive securing it to the rear display bezel.

Do not pry against the fragile glass LCD panel. Also, do not excessively bend the plastic as it may permanently deform.

Continue prying until the front display bezel is free along the right side of the display and behind the right clutch hinge.

Step 16

  • Use the flat end of a spudger to pry the front display bezel off the top edge of the display assembly.
  • It may be helpful to insert and twist the flat end of your spudger to enlarge the gap between the front & rear display bezels as you work your way around the edge of the display.
  • Continue separating until the top edge of the front display bezel is free from the display assembly.
  • Be careful when prying near the iSight camera board, as it has exposed circuitry and is delicate.

Use the flat end of a spudger to pry the front display bezel off the top edge of the display assembly.

It may be helpful to insert and twist the flat end of your spudger to enlarge the gap between the front & rear display bezels as you work your way around the edge of the display.

Continue separating until the top edge of the front display bezel is free from the display assembly.

Be careful when prying near the iSight camera board, as it has exposed circuitry and is delicate.

Step 17

  • Use your spudger to pry the left side of the front display bezel away from the display assembly.
  • Carefully pry up the area behind the left clutch hinge.
  • During reassembly, be sure the small plastic pegs on the front display bezel mate up with the holes in the rear display bezel (shown in red). Failure to do so will prevent the front display bezel from sitting flush against the rear bezel.

Use your spudger to pry the left side of the front display bezel away from the display assembly.

Carefully pry up the area behind the left clutch hinge.

During reassembly, be sure the small plastic pegs on the front display bezel mate up with the holes in the rear display bezel (shown in red). Failure to do so will prevent the front display bezel from sitting flush against the rear bezel.

Step 18

  • Slowly work your way across the lower edge of the front display bezel until it is free from the display assembly.
  • Be sure to pry up as far away from the LCD as possible, as it extends below the edge of the front display bezel.
  • When you get about half way across, pry up from the other side of the front display bezel’s lower edge to ease the process.

Slowly work your way across the lower edge of the front display bezel until it is free from the display assembly.

Be sure to pry up as far away from the LCD as possible, as it extends below the edge of the front display bezel.

When you get about half way across, pry up from the other side of the front display bezel’s lower edge to ease the process.

Step 19

  • Remove the front display bezel from the display assembly.
  • To help the adhesive avoid losing is tackiness, do not excessively handle the adhesive and be sure to keep it clean until you are ready for installation.

Remove the front display bezel from the display assembly.

To help the adhesive avoid losing is tackiness, do not excessively handle the adhesive and be sure to keep it clean until you are ready for installation.

Step 20

              Clutch Cover
  • Remove the two 3 mm Phillips screws securing the clutch cover to the rear display bezel.

Remove the two 3 mm Phillips screws securing the clutch cover to the rear display bezel.

Step 21

  • Insert the flat end of a spudger into the open end of the clutch cover and pry up to release it from the rear display bezel.
  • Pry up from both sides of the clutch cover until it is completely free from the display assembly.

Insert the flat end of a spudger into the open end of the clutch cover and pry up to release it from the rear display bezel.

Pry up from both sides of the clutch cover until it is completely free from the display assembly.

Step 22

  • Remove the clutch cover from the display assembly.

Remove the clutch cover from the display assembly.

Step 23

              LCD
  • Remove following six screws securing the LCD to the rear display bezel:
  • Four 3.4 mm Phillips.
  • Two 3 mm Phillips.

Remove following six screws securing the LCD to the rear display bezel:

Four 3.4 mm Phillips.

Two 3 mm Phillips.

Step 24

  • Do not try to remove the LCD yet. The circuitry along its lower edge is wedged in a gap along the lower edge of the display recess in the plastic display assembly.
  • Hold the display vertically and tip it enough to grab the top edge of the LCD and rotate it slightly out of the display assembly, being careful not to break the circuitry off its lower edge.

Do not try to remove the LCD yet. The circuitry along its lower edge is wedged in a gap along the lower edge of the display recess in the plastic display assembly.

Hold the display vertically and tip it enough to grab the top edge of the LCD and rotate it slightly out of the display assembly, being careful not to break the circuitry off its lower edge.

Step 25

  • Peel the piece of tape covering the display data cable connector away from the edge closest to the LCD.

Peel the piece of tape covering the display data cable connector away from the edge closest to the LCD.

Step 26

  • Use the tip of a spudger to flip up the thin steel retaining clip securing the display data cable to its socket on the LCD.
  • Pull the display data cable straight away from its socket on the LCD.
  • Lift the LCD out of the display assembly and set it aside.

Use the tip of a spudger to flip up the thin steel retaining clip securing the display data cable to its socket on the LCD.

Pull the display data cable straight away from its socket on the LCD.

Lift the LCD out of the display assembly and set it aside.

Step 27

              Display Data/Camera Cable
  • Remove the two small pieces of black tape securing the display data/camera cable to the rear display bezel.

Remove the two small pieces of black tape securing the display data/camera cable to the rear display bezel.

Step 28

  • Use the pointed tip of a spudger to pry the camera board off the display assembly.
  • Disconnect the camera cable by pulling its connector away from the socket on the camera board.

Use the pointed tip of a spudger to pry the camera board off the display assembly.

Disconnect the camera cable by pulling its connector away from the socket on the camera board.

Step 29

  • De-route the display data/camera cable from the slot cut into the rear display bezel.

De-route the display data/camera cable from the slot cut into the rear display bezel.

Step 30

  • Carefully pull the display data/camera cable out from under the frame attached to the rear display bezel and remove it from the display assembly.

Carefully pull the display data/camera cable out from under the frame attached to the rear display bezel and remove it from the display assembly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      29 other people completed this guide.

Author

                                      with 3 other contributors 


                    Andrew Bookholt

575,478 Reputation

                                      618 Guides authored                  



                       Badges:
                       47







                                                        +44 more badges

Paul van Gool - Jun 4, 2012

Reply

I hate apple! Freaks!!

oliveribarra - Jul 10, 2012

Reply

Where Can I buy the Display Data/Camera Cable?

I only found the installing guide..