Difficulty
Difficult
Steps
20
Time Required
Suggest a time??
Sections
6
- Access Door
- 2 steps
- Battery
- 1 step
- Lower Case
- 2 steps
- Display Assembly
- 9 steps
- Clutch Cover
- 3 steps
- Left Clutch Hinge
- 3 steps
Flags
0
BackMacBook Unibody A1278
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Access Door
- With the case closed, place the Unibody top-side down on a flat surface.
- Depress the grooved side of the access door release latch enough to grab the free end. Lift the release latch until it is vertical.
With the case closed, place the Unibody top-side down on a flat surface.
Depress the grooved side of the access door release latch enough to grab the free end. Lift the release latch until it is vertical.
1024
Step 2
- The access door should now be raised enough to lift it up and out of the Unibody.
The access door should now be raised enough to lift it up and out of the Unibody.
Step 3
Battery
- Be sure the access door release latch is vertical before proceeding.
- Grab the white plastic tab and pull the battery up and out of the Unibody.
Be sure the access door release latch is vertical before proceeding.
Grab the white plastic tab and pull the battery up and out of the Unibody.
Step 4
Lower Case
- Remove the following eight screws securing the lower case to the chassis:
- One 3 mm Phillips screw.
- Three 13.5 mm Phillips screws.
- Four 3.5 mm Phillips screws.
Remove the following eight screws securing the lower case to the chassis:
One 3 mm Phillips screw.
Three 13.5 mm Phillips screws.
Four 3.5 mm Phillips screws.
Step 5
- Using both hands, lift and remove the lower case off the upper case.
Using both hands, lift and remove the lower case off the upper case.
Step 6
Display Assembly
- Disconnect the camera cable by pulling the male end straight away from its socket.
- Be careful not to pull up on the cable as you remove it from the socket.
Disconnect the camera cable by pulling the male end straight away from its socket.
Be careful not to pull up on the cable as you remove it from the socket.
Step 7
- De-route the camera data cable from the channel in the optical drive.
De-route the camera data cable from the channel in the optical drive.
Step 8
- Remove the following screws securing the camera data cable and right speaker to the upper case:
- One 9.9 mm partially threaded Phillips screw
- One 9.6 mm threaded Phillips screw
- One 4 mm Phillips screw
- Slide the camera cable bracket out from under the subwoofer and remove it from the computer.
- The iSight cable has an eyelet through which passes the left-most screw in these pictures.
Remove the following screws securing the camera data cable and right speaker to the upper case:
One 9.9 mm partially threaded Phillips screw
One 9.6 mm threaded Phillips screw
One 4 mm Phillips screw
Slide the camera cable bracket out from under the subwoofer and remove it from the computer.
The iSight cable has an eyelet through which passes the left-most screw in these pictures.
Step 9
- Grab the plastic pull tab secured to the display data cable lock and rotate it toward the DC-in side of the computer.
- Pull the display data cable connector straight away from its socket.
- Make sure to pull the connector straight away and not straight up from its socket.
Grab the plastic pull tab secured to the display data cable lock and rotate it toward the DC-in side of the computer.
Pull the display data cable connector straight away from its socket.
Make sure to pull the connector straight away and not straight up from its socket.
Step 10
- Remove the following two screws from the display data cable bracket:
- One 7 mm Phillips screw.
- One 5 mm Phillips screw.
- Lift the display data cable bracket out of the upper case.
Remove the following two screws from the display data cable bracket:
One 7 mm Phillips screw.
One 5 mm Phillips screw.
Lift the display data cable bracket out of the upper case.
Step 11
- Remove the two outer 6 mm Torx screws securing each side of the display to the upper case (4 screws total).
Remove the two outer 6 mm Torx screws securing each side of the display to the upper case (4 screws total).
Step 12
- Open your MacBook so the display is perpendicular to the upper case.
- Place your opened MacBook on a table as pictured.
- While holding the display and upper case together with your left hand, remove the 6 mm Torx screw from the lower display bracket.
Open your MacBook so the display is perpendicular to the upper case.
Place your opened MacBook on a table as pictured.
While holding the display and upper case together with your left hand, remove the 6 mm Torx screw from the lower display bracket.
Step 13
- Be sure to hold the display and upper case together with your left hand. Failure to do so may cause the freed display/upper case to fall, potentially damaging each component.
- Remove the last remaining 6 mm Torx screw securing the display to the upper case.
Be sure to hold the display and upper case together with your left hand. Failure to do so may cause the freed display/upper case to fall, potentially damaging each component.
Remove the last remaining 6 mm Torx screw securing the display to the upper case.
Step 14
- Grab the upper case with your right hand and rotate it slightly toward the top of the display so the upper display bracket clears the edge of the upper case.
- Rotate the display slightly away from the upper case.
- Lift the display away from the upper case, minding any brackets or cables that may get caught.
Grab the upper case with your right hand and rotate it slightly toward the top of the display so the upper display bracket clears the edge of the upper case.
Rotate the display slightly away from the upper case.
Lift the display away from the upper case, minding any brackets or cables that may get caught.
Step 15
Clutch Cover
- Grab the clutch cover as shown and slide it toward the right side of the display.
- It should move about 1/4" and stop. Don’t force it beyond this point.
Grab the clutch cover as shown and slide it toward the right side of the display.
It should move about 1/4" and stop. Don’t force it beyond this point.
Step 16
- Gently rock the clutch cover back and forth on its long axis while pulling it away from the display.
- Do this action along the length of the clutch cover until you can lift it off the framework attaching it to the display.
Gently rock the clutch cover back and forth on its long axis while pulling it away from the display.
Do this action along the length of the clutch cover until you can lift it off the framework attaching it to the display.
Step 17
- Remove the clutch cover from the display.
Remove the clutch cover from the display.
Step 18
Left Clutch Hinge
- Remove the single 5.2 mm T6 Torx screw securing the left clutch hinge nearest the display glass.
Remove the single 5.2 mm T6 Torx screw securing the left clutch hinge nearest the display glass.
Step 19
- Remove the remaining two 5.2 mm T6 Torx screws securing the left clutch hinge to the display.
Remove the remaining two 5.2 mm T6 Torx screws securing the left clutch hinge to the display.
Step 20
- Remove the left clutch hinge from the display.
Remove the left clutch hinge from the display.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
11 other people completed this guide.
Author
with 2 other contributors
Walter Galan
682,038 Reputation
1,203 Guides authored
Badges:
54
+51 more badges