Difficulty

Moderate

Steps

7

Time Required

Suggest a time??

Sections

3

  • Lower Case
  • 2 steps
  • Battery Connector
  • 2 steps
  • Right Fan
  • 3 steps

Flags

0

  • BackMacBook Pro 15" Unibody Mid 2012

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Lower Case
  • Remove the following ten screws securing the lower case to the upper case:
  • Three 13.5 mm (14.1 mm) Phillips screws.
  • Seven 3 mm Phillips screws.
  • When removing these screws, note how they come out at a slight angle. They must be reinstalled the same way.

Remove the following ten screws securing the lower case to the upper case:

Three 13.5 mm (14.1 mm) Phillips screws.

Seven 3 mm Phillips screws.

When removing these screws, note how they come out at a slight angle. They must be reinstalled the same way.

1024

Step 2

  • Using both hands, lift the lower case near the vent to pop it off two clips securing it to the upper case.
  • Remove the lower case and set it aside.

Using both hands, lift the lower case near the vent to pop it off two clips securing it to the upper case.

Remove the lower case and set it aside.

Step 3

              Battery Connector
  • For certain repairs (e.g. hard drive), disconnecting the battery connector is not necessary but is recommended as it prevents any accidental shorting of electronics on the motherboard. If you do not disconnect the battery connector, please be careful as parts of the motherboard might be electrified.
  • Use the edge of a spudger to pry the battery connector upwards from its socket on the logic board.
  • It is useful to pry upward on both short sides of the connector to “walk” it out of its socket.

For certain repairs (e.g. hard drive), disconnecting the battery connector is not necessary but is recommended as it prevents any accidental shorting of electronics on the motherboard. If you do not disconnect the battery connector, please be careful as parts of the motherboard might be electrified.

Use the edge of a spudger to pry the battery connector upwards from its socket on the logic board.

It is useful to pry upward on both short sides of the connector to “walk” it out of its socket.

Step 4

  • Bend the battery cable slightly away from its socket on the logic board so it does not accidentally connect itself while you work.

Bend the battery cable slightly away from its socket on the logic board so it does not accidentally connect itself while you work.

Step 5

              Right Fan
  • Use a spudger to pry the fan connector straight up off the logic board.
  • It is useful to twist the spudger axially from beneath the fan cable wires to release the connector.
  • The fan socket and the fan connector can be seen in the second and third pictures. Be careful not to break the plastic fan socket off the logic board as you use your spudger to lift the fan connector straight up and out of its socket. The layout of the logic board shown in the second picture may look slightly different than your machine but the fan socket is the same.

Use a spudger to pry the fan connector straight up off the logic board.

It is useful to twist the spudger axially from beneath the fan cable wires to release the connector.

The fan socket and the fan connector can be seen in the second and third pictures. Be careful not to break the plastic fan socket off the logic board as you use your spudger to lift the fan connector straight up and out of its socket. The layout of the logic board shown in the second picture may look slightly different than your machine but the fan socket is the same.

Step 6

  • Remove three T6 Torx screws securing the right fan to the logic board and upper case.

Remove three T6 Torx screws securing the right fan to the logic board and upper case.

Step 7

  • Lift the right fan out of the upper case.

Lift the right fan out of the upper case.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      31 other people completed this guide.

Author

                                      with 3 other contributors 


                    Andrew Optimus Goldheart

Member since: 10/17/2009

491,689 Reputation

                                      411 Guides authored                  



                       Badges:
                       44







                                                        +41 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,767 Guides authored