Difficulty

Easy

Steps

11

Time Required

Suggest a time??

Sections

4

  • Access Door
  • 2 steps
  • Battery
  • 1 step
  • Lower Case
  • 2 steps
  • Feet
  • 6 steps

Flags

0

  • BackMacBook Pro 15" Unibody Late 2008 & Early 2009

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Access Door
  • With the case closed, place the Unibody top-side down on a flat surface.
  • Depress the grooved side of the access door release latch enough to grab the free end. Lift the release latch until it is vertical.

With the case closed, place the Unibody top-side down on a flat surface.

Depress the grooved side of the access door release latch enough to grab the free end. Lift the release latch until it is vertical.

1024

Step 2

  • The access door should now be raised enough to lift it up and out of the Unibody.

The access door should now be raised enough to lift it up and out of the Unibody.

Step 3

              Battery
  • Be sure the access door release latch is vertical before proceeding.
  • Grab the translucent plastic tab and pull the battery up and out of the Unibody.
  • If the latch is depressed it will lock the battery in place.

Be sure the access door release latch is vertical before proceeding.

Grab the translucent plastic tab and pull the battery up and out of the Unibody.

If the latch is depressed it will lock the battery in place.

Step 4

              Lower Case
  • Remove the following eight screws securing the lower case to the chassis:
  • One 5.4 mm Phillips screw.
  • Three 14 mm Phillips screws.
  • Four 3.5 mm Phillips screws.

Remove the following eight screws securing the lower case to the chassis:

One 5.4 mm Phillips screw.

Three 14 mm Phillips screws.

Four 3.5 mm Phillips screws.

Step 5

  • Using both hands, lift and remove the lower case off the upper case.

Using both hands, lift and remove the lower case off the upper case.

Step 6

              Feet
  • Remove any broken or damaged feet.
  • Remove any pieces from the old foot that may have broken off in the foot hole.
  • Use tweezers to peel up and remove the old adhesive tape from the foot pad.

Remove any broken or damaged feet.

Remove any pieces from the old foot that may have broken off in the foot hole.

Use tweezers to peel up and remove the old adhesive tape from the foot pad.

Step 7

  • Scrub the foot pad with adhesive remover to remove any remaining adhesive.

Scrub the foot pad with adhesive remover to remove any remaining adhesive.

Step 8

  • Wipe the foot pad with an alcohol prep pad to remove any residue left by the cleaner.

Wipe the foot pad with an alcohol prep pad to remove any residue left by the cleaner.

Step 9

  • Peel a replacement foot from the plastic backing.

Peel a replacement foot from the plastic backing.

Step 10

  • Align the new foot inside the foot pad.
  • Make sure the alignment nub on the foot is lined up with the small hole near the perimeter of the pad.
  • Lay the foot down while keeping it properly aligned.
  • Check for proper alignment from the inside of the lower case. Use tweezers to slide the alignment nub so it lines up with the hole.

Align the new foot inside the foot pad.

Make sure the alignment nub on the foot is lined up with the small hole near the perimeter of the pad.

Lay the foot down while keeping it properly aligned.

Check for proper alignment from the inside of the lower case. Use tweezers to slide the alignment nub so it lines up with the hole.

Step 11

  • Press the new foot down firmly with your finger and maintain pressure for 30 seconds to set the pressure sensitive adhesive. Support the other side of the cover while you press the foot down.
  • Repeat the last six steps for any broken or damaged feet.

Press the new foot down firmly with your finger and maintain pressure for 30 seconds to set the pressure sensitive adhesive. Support the other side of the cover while you press the foot down.

Repeat the last six steps for any broken or damaged feet.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 1 other contributor 


                    Adam O'Camb

Member since: 04/11/2015

173,479 Reputation

                                      418 Guides authored                  



                       Badges:
                       39







                                                        +36 more badges