Macbook Pro 15 Unibody 2 53 Ghz Mid 2009 Hard Drive Ir Sensor Cable Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Lower Case
2 steps
Battery
5 steps
Hard Drive
3 steps
Hard Drive/IR Sensor Cable
4 steps

Flags

BackMacBook Pro 15" Unibody 2.53 GHz Mid 2009
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Lower Case

Remove the following ten screws securing the lower case to the upper case:
Seven 3 mm Phillips screws.
Three 13.5 mm Phillips screws.

Remove the following ten screws securing the lower case to the upper case:

Seven 3 mm Phillips screws.

Three 13.5 mm Phillips screws.

1024

Step 2

Using both hands, lift the lower case near the vent to pop it off two clips securing it to the upper case.
Remove the lower case and set it aside.

Using both hands, lift the lower case near the vent to pop it off two clips securing it to the upper case.

Remove the lower case and set it aside.

Step 3

              Battery

Three Pentalobe screws secure the battery to the upper case. They can be removed with this special driver.
If you don’t have a Pentalobe driver, a 1.5 mm flathead screwdriver can be used in a pinch. Be sure the head of your flathead screwdriver fits snugly across two of the five “points” of the screw head before trying to break the screw free, as a loose fit will easily strip the screw head.
If the head of your screwdriver fits too loosely, find a bigger bit and file it down until it fits snugly before proceeding.
You do not necessarily have to follow steps 3-7 to remove the battery in order to replace the hard drive. However, it is recommended to remove all power sources from electronics before working on them.

Three Pentalobe screws secure the battery to the upper case. They can be removed with this special driver.

If you don’t have a Pentalobe driver, a 1.5 mm flathead screwdriver can be used in a pinch. Be sure the head of your flathead screwdriver fits snugly across two of the five “points” of the screw head before trying to break the screw free, as a loose fit will easily strip the screw head.

If the head of your screwdriver fits too loosely, find a bigger bit and file it down until it fits snugly before proceeding.

You do not necessarily have to follow steps 3-7 to remove the battery in order to replace the hard drive. However, it is recommended to remove all power sources from electronics before working on them.

Step 4

Remove the two exposed five-point Pentalobe screws along the top edge of the battery.

Remove the two exposed five-point Pentalobe screws along the top edge of the battery.

Step 5

Use the tip of a spudger to bend back the finger of the “Warning: Do not remove the battery” sticker while you remove the five-point Pentalobe screw hidden underneath.

Use the tip of a spudger to bend back the finger of the “Warning: Do not remove the battery” sticker while you remove the five-point Pentalobe screw hidden underneath.

Step 6

Lift the battery by its plastic pull tab and slide it away from the long edge of the upper case.
Do not try to completely remove the battery just yet.

Lift the battery by its plastic pull tab and slide it away from the long edge of the upper case.

Do not try to completely remove the battery just yet.

Step 7

Tilt the battery back enough to access the battery cable connector.
Pull the battery cable connector away from its socket on the logic board and remove the battery from the upper case.
If you’re installing a new battery, you should calibrate it as soon as possible.

Tilt the battery back enough to access the battery cable connector.

Pull the battery cable connector away from its socket on the logic board and remove the battery from the upper case.

If you’re installing a new battery, you should calibrate it as soon as possible.

Step 8

              Hard Drive

Remove two Phillips screws securing the hard drive bracket to the upper case.
These screws are captive to the hard drive bracket.
Lift the the retaining bracket out of the upper case.

Remove two Phillips screws securing the hard drive bracket to the upper case.

These screws are captive to the hard drive bracket.

Lift the the retaining bracket out of the upper case.

Step 9

Lift the hard drive by its pull tab and pull it out of the chassis, minding the cable attaching it to the computer.

Lift the hard drive by its pull tab and pull it out of the chassis, minding the cable attaching it to the computer.

Step 10

Remove the hard drive cable by pulling its connector straight away from the hard drive.

Remove the hard drive cable by pulling its connector straight away from the hard drive.

Step 11

              Hard Drive/IR Sensor Cable

Remove the following four screws securing the hard drive and IR sensor cable to the upper case:
Two 1.5 mm Phillips screws.
Two 4 mm Phillips screws.

Remove the following four screws securing the hard drive and IR sensor cable to the upper case:

Two 1.5 mm Phillips screws.

Two 4 mm Phillips screws.

Step 12

Slide the hard drive and IR sensor bracket away from the edge of the upper case.
Carefully peel the hard drive and IR sensor cable from the upper case.

Slide the hard drive and IR sensor bracket away from the edge of the upper case.

Carefully peel the hard drive and IR sensor cable from the upper case.

Step 13

Use the flat end of a spudger to pry the hard drive cable connector up off the logic board.
Lift the hard drive and IR sensor assembly out of the upper case.

Use the flat end of a spudger to pry the hard drive cable connector up off the logic board.

Lift the hard drive and IR sensor assembly out of the upper case.

Step 14

Your replacement part may or may not come with the front (sensor) bracket. If it does not, you’ll need to transfer it to your new cable.
Use the tip of a spudger to flip the ZIF connector on the hard drive cable.
Gently pull the sensor bracket cable out of the ZIF connector.
Use the flat end of a spudger to pry the hard drive cable up off the sensor bracket.
Remove the adhesive backing from your new hard drive cable, stick it onto the sensor bracket, and connect the sensor bracket cable.

Your replacement part may or may not come with the front (sensor) bracket. If it does not, you’ll need to transfer it to your new cable.

Use the tip of a spudger to flip the ZIF connector on the hard drive cable.

Gently pull the sensor bracket cable out of the ZIF connector.

Use the flat end of a spudger to pry the hard drive cable up off the sensor bracket.

Remove the adhesive backing from your new hard drive cable, stick it onto the sensor bracket, and connect the sensor bracket cable.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      54 other people completed this guide.

Author

                                      with 5 other contributors

                    Walter Galan

682,038 Reputation

                                      1,203 Guides authored                  



                       Badges:
                       54







                                                        +51 more badges

Introduction#

What you need#

Introduction

What you need