Macbook Pro 15 Retina Display Mid 2014 Feet Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          5 - 10 minutes

Sections

Lower Case
3 steps
Feet
7 steps

Flags

BackMacBook Pro 15" Retina Display Mid 2014
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Lower Case

Remove the following P5 pentalobe screws securing the lower case to the MacBook Pro:
Eight 3.1 mm
Two 2.3 mm

Remove the following P5 pentalobe screws securing the lower case to the MacBook Pro:

Eight 3.1 mm

Two 2.3 mm

1024

Step 2

Lifting from the edge nearest the clutch cover, lift the lower case off the MacBook Pro.

Lifting from the edge nearest the clutch cover, lift the lower case off the MacBook Pro.

Step 3

The lower case has two plastic pegs (red) that fit into plastic clips in the upper case (orange).
During reassembly, gently push down the center of the lower case to reattach the case to its two plastic clips.

The lower case has two plastic pegs (red) that fit into plastic clips in the upper case (orange).

During reassembly, gently push down the center of the lower case to reattach the case to its two plastic clips.

Step 4

              Feet

Peel away any stickers from the backside of the rear case covering the feet you have chosen to replace.
Any stickers you remove will most likely be unsalvageable for re-use. That’s okay! Your MacBook does not need them to function.

Peel away any stickers from the backside of the rear case covering the feet you have chosen to replace.

Any stickers you remove will most likely be unsalvageable for re-use. That’s okay! Your MacBook does not need them to function.

Step 5

Remove any broken or damaged feet.
If the foot you are replacing is still intact, you can use your tweezers push it out from the inside.
If the old foot is difficult to remove, use a hair dryer or a heat gun to apply some heat to the area and loosen the adhesive.

Remove any broken or damaged feet.

If the foot you are replacing is still intact, you can use your tweezers push it out from the inside.

If the old foot is difficult to remove, use a hair dryer or a heat gun to apply some heat to the area and loosen the adhesive.

Step 6

Scrub the foot cavity with adhesive remover to remove any remaining adhesive.

Scrub the foot cavity with adhesive remover to remove any remaining adhesive.

Step 7

Wipe the foot cavity with an isopropyl alcohol prep pad to remove any cleaner residue and prep the area for the adhesive on the new foot.

Wipe the foot cavity with an isopropyl alcohol prep pad to remove any cleaner residue and prep the area for the adhesive on the new foot.

Step 8

Peel a replacement foot from the plastic backing.
The adhesive is fairly strong—make sure that you are peeling the foot up, not tearing the plastic backing.

Peel a replacement foot from the plastic backing.

The adhesive is fairly strong—make sure that you are peeling the foot up, not tearing the plastic backing.

Step 9

Align the new foot inside the cavity.
Make sure the alignment nub on the foot is lined up with the small hole near the perimeter of the pad.
You may want to use a pencil to lightly mark where the alignment nub is located. Be careful not to scratch the lower case with your pencil.
Lay the foot down while keeping it properly aligned.
Check for proper alignment from the inside of the case. The alignment nub should be slightly visible through the alignment hole.

Align the new foot inside the cavity.

Make sure the alignment nub on the foot is lined up with the small hole near the perimeter of the pad.

You may want to use a pencil to lightly mark where the alignment nub is located. Be careful not to scratch the lower case with your pencil.

Lay the foot down while keeping it properly aligned.

Check for proper alignment from the inside of the case. The alignment nub should be slightly visible through the alignment hole.

Step 10

Press the new foot into place firmly with your finger, then apply pressure by pinching the foot from either side of the case with your finger and your thumb.
Maintain pressure for 30 seconds to set the pressure-sensitive adhesive.
Repeat the last seven steps for any remaining broken or worn feet.

Press the new foot into place firmly with your finger, then apply pressure by pinching the foot from either side of the case with your finger and your thumb.

Maintain pressure for 30 seconds to set the pressure-sensitive adhesive.

Repeat the last seven steps for any remaining broken or worn feet.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      14 other people completed this guide.

Author

                                      with 1 other contributor

                    Taylor Dixon

Member since: 06/26/2018

62,097 Reputation

                                      94 Guides authored                  



                       Badges:
                       40







                                                        +37 more badges

Team

                       Teardown Team                        

                                                  Member of Teardown Team 



                    Community                     


                                            2 Members                     


                                            2,047 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team