Macbook Pro 15 Retina Display Late 2013 Right Fan Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          25 minutes - 1 hour

Sections

Lower Case
2 steps
Battery Connector
2 steps
AirPort/Camera Cable
4 steps
I/O Board Cable
1 step
Right Fan
5 steps

Flags

BackMacBook Pro 15" Retina Display Late 2013
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Lower Case

Remove the following P5 pentalobe screws securing the lower case to the MacBook Pro:
Eight 3.0 mm
Two 2.3 mm

Remove the following P5 pentalobe screws securing the lower case to the MacBook Pro:

Eight 3.0 mm

Two 2.3 mm

1024

Step 2

Lifting from the edge nearest the clutch cover, lift the lower case off the MacBook Pro.
Set the lower case aside.

Lifting from the edge nearest the clutch cover, lift the lower case off the MacBook Pro.

Set the lower case aside.

Step 3

              Battery Connector

Peel back the warning label covering the battery connector.

Peel back the warning label covering the battery connector.

Step 4

Using the flat end of a spudger, gently pry the battery connector straight up out of its socket on the logic board.
Bend the battery cables back and out of the way, ensuring that the battery connector doesn’t accidentally make contact with the logic board.

Using the flat end of a spudger, gently pry the battery connector straight up out of its socket on the logic board.

Bend the battery cables back and out of the way, ensuring that the battery connector doesn’t accidentally make contact with the logic board.

Step 5

              AirPort/Camera Cable

Use a spudger or tweezers to pry the three AirPort antenna cables straight up off of their sockets on the AirPort board.
The cable connection points are fragile. Be careful to lift only on the connector, and not on the socket or cable.
To reconnect, align the connector carefully into position over the socket, and press it down firmly with the flat of your spudger.

Use a spudger or tweezers to pry the three AirPort antenna cables straight up off of their sockets on the AirPort board.

The cable connection points are fragile. Be careful to lift only on the connector, and not on the socket or cable.

To reconnect, align the connector carefully into position over the socket, and press it down firmly with the flat of your spudger.

Step 6

Use the tip of a spudger to push the camera cable’s plug toward the fan and out of its socket on the logic board.
The plug in the photo has six connections, but some models have twelve connections. The process of removing the plug from its socket is the same for both.
If the camera cable’s plug won’t come easily out of its socket on the logic board, fold back the rubber cover over the fan to gain access to the cable, then gently pull on the cable while using the spudger to gently push the plug out of its socket.
Be sure to push parallel to the board, first on one side, then the other, to slowly “walk” the plug out of its socket. Do not pry up, or you will damage the socket.

Use the tip of a spudger to push the camera cable’s plug toward the fan and out of its socket on the logic board.

The plug in the photo has six connections, but some models have twelve connections. The process of removing the plug from its socket is the same for both.

If the camera cable’s plug won’t come easily out of its socket on the logic board, fold back the rubber cover over the fan to gain access to the cable, then gently pull on the cable while using the spudger to gently push the plug out of its socket.

Be sure to push parallel to the board, first on one side, then the other, to slowly “walk” the plug out of its socket. Do not pry up, or you will damage the socket.

Step 7

Insert the flat end of a spudger underneath the rubber heat sink cover on the right fan.
Slide the spudger underneath the length of the cover, releasing the adhesive.
Lift the cover and flip it back so that you can access the cables underneath.

Insert the flat end of a spudger underneath the rubber heat sink cover on the right fan.

Slide the spudger underneath the length of the cover, releasing the adhesive.

Lift the cover and flip it back so that you can access the cables underneath.

Step 8

Use your fingers to pull the AirPort/Camera cables up off the fan.
The cables are adhered to the fan, so peel them up carefully to avoid damaging them.
Carefully de-route the cables from the plastic cable guide.

Use your fingers to pull the AirPort/Camera cables up off the fan.

The cables are adhered to the fan, so peel them up carefully to avoid damaging them.

Carefully de-route the cables from the plastic cable guide.

Step 9

              I/O Board Cable

If your I/O Board cable’s connectors have notches in the padding, you will need to release a locking lever underneath the notch in order to remove the cable. If this is the case, don’t pry up on the connector until the levers are unlatched.
Using the flat end of a spudger, pry the I/O Board connector straight up out of its socket on the logic board.
During reassembly, connect this end first, as it does not flex.
In a similar fashion, remove the I/O Board cable connector from its socket on the I/O Board.
Remove the I/O Board cable from the MacBook Pro.

If your I/O Board cable’s connectors have notches in the padding, you will need to release a locking lever underneath the notch in order to remove the cable. If this is the case, don’t pry up on the connector until the levers are unlatched.

Using the flat end of a spudger, pry the I/O Board connector straight up out of its socket on the logic board.

During reassembly, connect this end first, as it does not flex.

In a similar fashion, remove the I/O Board cable connector from its socket on the I/O Board.

Remove the I/O Board cable from the MacBook Pro.

Step 10

              Airport Card

Remove the single 2.9 mm T5 (sometimes T6) Torx screw securing the AirPort card to the logic board.

Remove the single 2.9 mm T5 (sometimes T6) Torx screw securing the AirPort card to the logic board.

Step 11

Grasp the sides of the AirPort card and lift it up to a shallow angle (5-10˚) to separate the light adhesive adhering it to the logic board.
Pull the AirPort card parallel out of its connector on the logic board to remove it.

Grasp the sides of the AirPort card and lift it up to a shallow angle (5-10˚) to separate the light adhesive adhering it to the logic board.

Pull the AirPort card parallel out of its connector on the logic board to remove it.

Step 12

Use the tip of a spudger to flip up the retaining flap on the right fan ribbon cable ZIF socket.
Be sure you are prying up on the hinged retaining flap, not the socket itself.
Starting at the top of the cable, slide a plastic opening tool under the right fan cable to free it from the logic board.
Use caution when freeing the cable, as it is strongly adhered to the logic board.

Use the tip of a spudger to flip up the retaining flap on the right fan ribbon cable ZIF socket.

Be sure you are prying up on the hinged retaining flap, not the socket itself.

Starting at the top of the cable, slide a plastic opening tool under the right fan cable to free it from the logic board.

Use caution when freeing the cable, as it is strongly adhered to the logic board.

Step 13

Remove the following three screws securing the right fan to the logic board:
One 4.4 mm T5 Torx screw
One 3.9 mm T5 Wide Head Torx screw
One 5.0 mm T5 Torx screw with 2 mm collar

Remove the following three screws securing the right fan to the logic board:

One 4.4 mm T5 Torx screw

One 3.9 mm T5 Wide Head Torx screw

One 5.0 mm T5 Torx screw with 2 mm collar

Step 14

Lift and remove the right fan out from the MacBook Pro.
When reinstalling the fan, it’s easiest connect the fan ribbon cable as you drop the fan in place, rather than after you’ve installed the three fan screws.

Lift and remove the right fan out from the MacBook Pro.

When reinstalling the fan, it’s easiest connect the fan ribbon cable as you drop the fan in place, rather than after you’ve installed the three fan screws.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      16 other people completed this guide.

Author

                                      with 4 other contributors

                    Andrew Optimus Goldheart

Member since: 10/17/2009

491,689 Reputation

                                      411 Guides authored                  



                       Badges:
                       44







                                                        +41 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,767 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team