Macbook Pro 15 Core Duo Model A1150 Upper Case Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Battery
1 step
Memory Door
2 steps
Upper Case
7 steps
Upper Case
14 steps

Flags

BackMacBook Pro 15" Core Duo Model A1150
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.

Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.

1024

Step 2

              Memory Door

Remove the three identical Phillips screws from the memory door.
Make sure to record which sets of screws came from where. This will help when re-assembling.

Remove the three identical Phillips screws from the memory door.

Make sure to record which sets of screws came from where. This will help when re-assembling.

Step 3

Lift the memory door up enough to get a grip on it, and slide it toward you, pulling it away from the casing.

Lift the memory door up enough to get a grip on it, and slide it toward you, pulling it away from the casing.

Step 4

              Upper Case

Remove the two Phillips screws in the battery compartment near the latch.

Remove the two Phillips screws in the battery compartment near the latch.

Step 5

Remove the following 6 screws:
Two 10 mm T6 Torx screws on either side of the RAM slot.
Four 14.5 mm Phillips screws along the hinge.

Remove the following 6 screws:

Two 10 mm T6 Torx screws on either side of the RAM slot.

Four 14.5 mm Phillips screws along the hinge.

Step 6

Remove the four Phillips screws on the port side of the computer.

Remove the four Phillips screws on the port side of the computer.

Step 7

Rotate the computer 90 degrees and remove the two Phillips screws from the rear of the computer.

Rotate the computer 90 degrees and remove the two Phillips screws from the rear of the computer.

Step 8

Rotate the computer 90 degrees again and remove the four Phillips screws from the side of the computer.

Rotate the computer 90 degrees again and remove the four Phillips screws from the side of the computer.

Step 9

Do not yank the upper case off quickly. The case is attached to the logic board via a ribbon cable.
Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case. This stage can be quite tricky. Over the DVD reader are 4 tabs set back which pull out vertically.
Note that the two small tongues on the left hand front of the upper case may bend while you remove the upper case. When re-installing, you may need to bend them back to fit in the grooves in the lower case.

Do not yank the upper case off quickly. The case is attached to the logic board via a ribbon cable.

Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case. This stage can be quite tricky. Over the DVD reader are 4 tabs set back which pull out vertically.

Note that the two small tongues on the left hand front of the upper case may bend while you remove the upper case. When re-installing, you may need to bend them back to fit in the grooves in the lower case.

Step 10

Disconnect the trackpad and keyboard ribbon cable from the logic board, removing tape as necessary.
Remove the upper case.

Disconnect the trackpad and keyboard ribbon cable from the logic board, removing tape as necessary.

Remove the upper case.

Step 11

              Upper Case

Use a spudger to pry up the translucent plastic sheath covering the keyboard connector.

Use a spudger to pry up the translucent plastic sheath covering the keyboard connector.

Step 12

Use the tip of a spudger to flip up the black plastic flaps locking down the keyboard and keyboard backlight ribbon cables.

Use the tip of a spudger to flip up the black plastic flaps locking down the keyboard and keyboard backlight ribbon cables.

Step 13

Slide the orange keyboard backlight ribbon out of its connector.

Slide the orange keyboard backlight ribbon out of its connector.

Step 14

Peel up the orange tape covering the keyboard backlight connector.
Use the tip of a spudger to flip up the brown plastic flap locking down the keyboard backlight ribbon cable.

Peel up the orange tape covering the keyboard backlight connector.

Use the tip of a spudger to flip up the brown plastic flap locking down the keyboard backlight ribbon cable.

Step 15

Use a spudger or your finger to slide the keyboard backlight ribbon out of its connector.

Use a spudger or your finger to slide the keyboard backlight ribbon out of its connector.

Step 16

Carefully peel up the orange ribbon cable which carries the power and sleep signals, removing tape as necessary.

Carefully peel up the orange ribbon cable which carries the power and sleep signals, removing tape as necessary.

Step 17

Peel back the black protective sheath on the right side of the upper case. It is not necessary to fully remove this shield. Simply peel it back enough to access the screws beneath.

Peel back the black protective sheath on the right side of the upper case. It is not necessary to fully remove this shield. Simply peel it back enough to access the screws beneath.

Step 18

Peel back the black protective sheath on the left side of the upper case. It is not necessary to fully remove this shield. Simply peel it back enough to access the screws beneath.

Peel back the black protective sheath on the left side of the upper case. It is not necessary to fully remove this shield. Simply peel it back enough to access the screws beneath.

Step 19

Remove the ten identical Phillips screws attaching the keyboard to the casing.

Remove the ten identical Phillips screws attaching the keyboard to the casing.

Step 20

There are four locking tabs along the back edge of the keyboard holding it in place. These tabs must be straightened before you can remove the keyboard.

There are four locking tabs along the back edge of the keyboard holding it in place. These tabs must be straightened before you can remove the keyboard.

Step 21

The first frame shows a tab in the “locked” position and the second frame shows the same tab in the “unlocked” position.
Use needlenose pliers or a spudger to bend each of the four tabs so that they are all in the “unlocked” position.

The first frame shows a tab in the “locked” position and the second frame shows the same tab in the “unlocked” position.

Use needlenose pliers or a spudger to bend each of the four tabs so that they are all in the “unlocked” position.

Step 22

Slide the keyboard ribbon out of its connector.
If the keyboard ribbon won’t slide out, make sure that the black plastic flap holding the ribbon in place is vertical.

Slide the keyboard ribbon out of its connector.

If the keyboard ribbon won’t slide out, make sure that the black plastic flap holding the ribbon in place is vertical.

Step 23

Place the upper casing on its edge and use a spudger to push the keyboard away from the casing, poking the spudger through the central keyboard screw hole. Grasp the keyboard as it separates from the casing.

Place the upper casing on its edge and use a spudger to push the keyboard away from the casing, poking the spudger through the central keyboard screw hole. Grasp the keyboard as it separates from the casing.

Step 24

Maintaining your hold on the keyboard, lay the casing flat and gently bow the keyboard until the two tabs on either side of the keyboard come free.
Slide the keyboard away from the trackpad and out of the upper case.

Maintaining your hold on the keyboard, lay the casing flat and gently bow the keyboard until the two tabs on either side of the keyboard come free.

Slide the keyboard away from the trackpad and out of the upper case.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.

Author

                                      with 5 other contributors

                    iRobot

Member since: 09/24/2009

1 Reputation

                                      646 Guides authored                  



                       Badges:
                       36







                                                        +33 more badges

Introduction#

What you need#

Introduction

What you need