Macbook Pro 15 Core Duo Model A1150 Pram Battery Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Battery
1 step
Memory Door
2 steps
Upper Case
7 steps
Optical Drive
3 steps
PRAM Battery
2 steps

Flags

BackMacBook Pro 15" Core Duo Model A1150
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.

Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.

1024

Step 2

              Memory Door

Remove the three identical Phillips screws from the memory door.
Make sure to record which sets of screws came from where. This will help when re-assembling.

Remove the three identical Phillips screws from the memory door.

Make sure to record which sets of screws came from where. This will help when re-assembling.

Step 3

Lift the memory door up enough to get a grip on it, and slide it toward you, pulling it away from the casing.

Lift the memory door up enough to get a grip on it, and slide it toward you, pulling it away from the casing.

Step 4

              Upper Case

Remove the two Phillips screws in the battery compartment near the latch.

Remove the two Phillips screws in the battery compartment near the latch.

Step 5

Remove the following 6 screws:
Two 10 mm T6 Torx screws on either side of the RAM slot.
Four 14.5 mm Phillips screws along the hinge.

Remove the following 6 screws:

Two 10 mm T6 Torx screws on either side of the RAM slot.

Four 14.5 mm Phillips screws along the hinge.

Step 6

Remove the four Phillips screws on the port side of the computer.

Remove the four Phillips screws on the port side of the computer.

Step 7

Rotate the computer 90 degrees and remove the two Phillips screws from the rear of the computer.

Rotate the computer 90 degrees and remove the two Phillips screws from the rear of the computer.

Step 8

Rotate the computer 90 degrees again and remove the four Phillips screws from the side of the computer.

Rotate the computer 90 degrees again and remove the four Phillips screws from the side of the computer.

Step 9

Do not yank the upper case off quickly. The case is attached to the logic board via a ribbon cable.
Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case. This stage can be quite tricky. Over the DVD reader are 4 tabs set back which pull out vertically.
Note that the two small tongues on the left hand front of the upper case may bend while you remove the upper case. When re-installing, you may need to bend them back to fit in the grooves in the lower case.

Do not yank the upper case off quickly. The case is attached to the logic board via a ribbon cable.

Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case. This stage can be quite tricky. Over the DVD reader are 4 tabs set back which pull out vertically.

Note that the two small tongues on the left hand front of the upper case may bend while you remove the upper case. When re-installing, you may need to bend them back to fit in the grooves in the lower case.

Step 10

Disconnect the trackpad and keyboard ribbon cable from the logic board, removing tape as necessary.
Remove the upper case.

Disconnect the trackpad and keyboard ribbon cable from the logic board, removing tape as necessary.

Remove the upper case.

Step 11

              Optical Drive

Disconnect the orange SuperDrive ribbon cable from the logic board, removing tape as necessary.

Disconnect the orange SuperDrive ribbon cable from the logic board, removing tape as necessary.

Step 12

Remove the following 3 screws:
Two 3.3 mm silver Phillips screws on either side of the SuperDrive.
One 4.8 mm black Phillips screw at the top right corner of the drive.
The 4.8mm screw may be a T6 Torx

Remove the following 3 screws:

Two 3.3 mm silver Phillips screws on either side of the SuperDrive.

One 4.8 mm black Phillips screw at the top right corner of the drive.

The 4.8mm screw may be a T6 Torx

Step 13

Lift the optical drive up and out of the computer.

Lift the optical drive up and out of the computer.

Step 14

              PRAM Battery

Disconnect the PRAM battery cable from the bottom right corner of the logic board.

Disconnect the PRAM battery cable from the bottom right corner of the logic board.

Step 15

Use a spudger to pry up the PRAM battery from the lower case.
Lift the PRAM battery out of the computer.

Use a spudger to pry up the PRAM battery from the lower case.

Lift the PRAM battery out of the computer.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      10 other people completed this guide.

Author

                                      with 1 other contributor

                    iRobot

Member since: 09/24/2009

1 Reputation

                                      646 Guides authored                  



                       Badges:
                       36







                                                        +33 more badges

Introduction#

What you need#

Introduction

What you need