Macbook Pro 15 Core 2 Duo Models A1226 And A1260 Hard Drive Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          45 minutes - 2 hours

Sections

Battery
1 step
RAM Shield
1 step
Upper Case
7 steps
Hard Drive
2 steps
Hard Drive
2 steps

Flags

BackMacBook Pro 15" Core 2 Duo Models A1226 & A1260
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.

Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.

1024

Step 2

              RAM Shield

Remove the three identical 2mm Phillips screws from the memory door.
Lift the memory door up enough to grip it and slide it toward you, pulling it away from the casing.

Remove the three identical 2mm Phillips screws from the memory door.

Lift the memory door up enough to grip it and slide it toward you, pulling it away from the casing.

Step 3

              Upper Case

Remove the two 2.8 mm Phillips screws in the battery compartment near the latch.

Remove the two 2.8 mm Phillips screws in the battery compartment near the latch.

Step 4

Remove the following 6 screws:
Two 10 mm T6 Torx screws on either side of the RAM slot.
Four 14.5 mm Phillips screws along the hinge.

Remove the following 6 screws:

Two 10 mm T6 Torx screws on either side of the RAM slot.

Four 14.5 mm Phillips screws along the hinge.

Step 5

Remove the four 3.2 mm PH00 Phillips screws on the port side of the computer.

Remove the four 3.2 mm PH00 Phillips screws on the port side of the computer.

Step 6

Rotate the computer 90 degrees and remove the two 3.2 mm Phillips screws from the rear of the computer.

Rotate the computer 90 degrees and remove the two 3.2 mm Phillips screws from the rear of the computer.

Step 7

Rotate the computer 90 degrees again and remove the four 3.2 mm Phillips screws from the side of the computer.

Rotate the computer 90 degrees again and remove the four 3.2 mm Phillips screws from the side of the computer.

Step 8

Do not yank the upper case off quickly. The case is attached to the logic board via a ribbon cable.
Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case.
There are four plastic clips above the DVD slot, and another above and to the left of the IR sensor. These clips can be very difficult to disengage without prying. They can also be difficult to re-engage during reassembly.
Reassembly Tip: Press down firmly on the tip of the top case above the location of each clip until you hear a snap to reseat them in their slots.
Reassembly Tip: The two center DVD clips will rarely snap back into place properly without help, and downward pressure will instead simply deform the frame around the DVD slot. Support the frame by inserting a plastic spudger into the DVD slot directly under the clip location until it is snug, then press down until you hear the snap.

Do not yank the upper case off quickly. The case is attached to the logic board via a ribbon cable.

Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case.

There are four plastic clips above the DVD slot, and another above and to the left of the IR sensor. These clips can be very difficult to disengage without prying. They can also be difficult to re-engage during reassembly.

Reassembly Tip: Press down firmly on the tip of the top case above the location of each clip until you hear a snap to reseat them in their slots.

Reassembly Tip: The two center DVD clips will rarely snap back into place properly without help, and downward pressure will instead simply deform the frame around the DVD slot. Support the frame by inserting a plastic spudger into the DVD slot directly under the clip location until it is snug, then press down until you hear the snap.

Step 9

Disconnect the trackpad and keyboard ribbon cable from the logic board, removing tape as necessary.
Note: It is possible to replace the hard drive without disconnecting the keyboard from the chassis, but it will need to be held upright to keep it out of the way, while still allowing you both hands to work on the drive removal.
Be careful when removing the keyboard-trackpad ribbon cable to ensure that the rear of the upper case is disengaged from the area near the hinge. It is easy to accidentally bend the screw receivers on either side of the keyboard.
Remove the upper case.

Disconnect the trackpad and keyboard ribbon cable from the logic board, removing tape as necessary.

Note: It is possible to replace the hard drive without disconnecting the keyboard from the chassis, but it will need to be held upright to keep it out of the way, while still allowing you both hands to work on the drive removal.

Be careful when removing the keyboard-trackpad ribbon cable to ensure that the rear of the upper case is disengaged from the area near the hinge. It is easy to accidentally bend the screw receivers on either side of the keyboard.

Remove the upper case.

Step 10

              Hard Drive

Disconnect the orange hard drive ribbon cable from the logic board.
Remove tape as necessary and use a spudger (or carefully push a credit card under the tape) to carefully loosen the adhesive securing the sleep light and IR sensor connectors to the top of the hard drive.
You may find it best to loosen the left edge, then the right edge, then the center of the tape to attack it from all points, so as to gently apply force to the smallest possible sticky surface.

Disconnect the orange hard drive ribbon cable from the logic board.

Remove tape as necessary and use a spudger (or carefully push a credit card under the tape) to carefully loosen the adhesive securing the sleep light and IR sensor connectors to the top of the hard drive.

You may find it best to loosen the left edge, then the right edge, then the center of the tape to attack it from all points, so as to gently apply force to the smallest possible sticky surface.

Step 11

Remove the two 8.2 mm T6 Torx screws securing the hard drive retaining bracket to the lower case.
Use a spudger if the hard drive ribbon cable is firmly glued to the top of the drive. You might have to work slowly in order to not damage it.
Lift the hard drive retaining bracket up and out of the computer.
Lift up the hard drive with one hand and use your other hand to disconnect the hard drive cable.

Remove the two 8.2 mm T6 Torx screws securing the hard drive retaining bracket to the lower case.

Use a spudger if the hard drive ribbon cable is firmly glued to the top of the drive. You might have to work slowly in order to not damage it.

Lift the hard drive retaining bracket up and out of the computer.

Lift up the hard drive with one hand and use your other hand to disconnect the hard drive cable.

Step 12

              Hard Drive

Remove the two silver T6 6 mm Torx screws from the left side of the hard drive.
You’ll need to transfer these screws to your new hard drive if you’re changing drives.

Remove the two silver T6 6 mm Torx screws from the left side of the hard drive.

You’ll need to transfer these screws to your new hard drive if you’re changing drives.

Step 13

Remove the two black T6 Torx screws and white rubber bumpers from the right side of the hard drive.
You’ll need to transfer these screws and bumpers to your new hard drive if you’re changing drives.
If you are installing a new hard drive, we have an OS X install guide to get you up and running.

Remove the two black T6 Torx screws and white rubber bumpers from the right side of the hard drive.

You’ll need to transfer these screws and bumpers to your new hard drive if you’re changing drives.

If you are installing a new hard drive, we have an OS X install guide to get you up and running.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      1089 other people completed this guide.

Author

                                      with 12 other contributors

                    Walter Galan

682,038 Reputation

                                      1,203 Guides authored                  



                       Badges:
                       54







                                                        +51 more badges

Andreas Zowislo - Nov 4, 2010

Hi folks, is it possible to inserting a new 1 GB 2,5" HDD with a thickness of 12.5 mm into the MBP?

can anyone help me?

Sorry about my bad english…

Andreas from germany

Alex Jenner - Nov 28, 2010

Not to the pre-unibody MBPs it isn’t possible, no. Maximum size 9.5 mm drives

Uncle Jim - Dec 8, 2010

I used the A1260 hard drive replacement guide to swop out a Western Digital Scorpio SATA (WD3200BEVT) 320 Gig 5400rpm for a Western Digital SATA (ST9750420AS) Momentus 750 Gig 7200rpm. (http://www.seagate.com/www/en-us/product…) The whole operation went flawlessly thanks to the guide. The improvement in speed / access with the bigger, faster hard drive is very noticeable. Just to let people know that the installation of a 750 gig drive is an accomplished fact in a A1260 series MacBook Pro.

HansO - Apr 24, 2011

Thanks for the very thoroughly and easy-to-follow guide. I’m no technical genius, but thanks to the guide I manage to replace the original disc with a Toshiba THNS 512GG8BBAA. I printed out the instructions and attached the screws with scotch to the right picture as I went along - not a chance of mixing or loosing the screws. It all went well, and the improvement is awesome!

Robert Lied - Jun 15, 2011

After some trepidation, it all came together flawlessly in about an hour. Great guide, and good advice in the notes about organizing those 27 screws. This will put at least another year of life in my aging Macbook.

Introduction#

What you need#

Introduction

What you need