Difficulty

Difficult

Steps

14

Time Required

Suggest a time??

Sections

4

  • Battery
  • 1 step
  • RAM Shield
  • 2 steps
  • Upper Case
  • 7 steps
  • Left Ambient Light Sensor
  • 4 steps

Flags

0

  • BackMacBook Pro 15" Core 2 Duo Model A1211

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.

Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.

1024

Step 2

              RAM Shield
  • Remove the three identical Phillips screws from the memory door.

Remove the three identical Phillips screws from the memory door.

Step 3

  • Lift the memory door up enough to get a grip on it, and slide it toward you, pulling it away from the casing.

Lift the memory door up enough to get a grip on it, and slide it toward you, pulling it away from the casing.

Step 4

              Upper Case
  • Remove the two 2.8 mm Phillips screws in the battery compartment near the latch.

Remove the two 2.8 mm Phillips screws in the battery compartment near the latch.

Step 5

  • Remove the following 6 screws:
  • Two 10 mm T6 Torx screws on either side of the RAM slot.
  • Four 14.5 mm Phillips screws along the hinge.

Remove the following 6 screws:

Two 10 mm T6 Torx screws on either side of the RAM slot.

Four 14.5 mm Phillips screws along the hinge.

Step 6

  • Remove the four 3.2 mm Phillips screws on the port side of the computer.

Remove the four 3.2 mm Phillips screws on the port side of the computer.

Step 7

  • Rotate the computer 90 degrees and remove the two 3.2 mm Phillips screws from the rear of the computer.

Rotate the computer 90 degrees and remove the two 3.2 mm Phillips screws from the rear of the computer.

Step 8

  • Rotate the computer 90 degrees again and remove the four 3.2 mm Phillips screws from the side of the computer.

Rotate the computer 90 degrees again and remove the four 3.2 mm Phillips screws from the side of the computer.

Step 9

  • Do not yank the upper case off quickly. The case is attached to the logic board via a ribbon cable.
  • Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case (there are some hidden plastic clips that need to be clicked off).

Do not yank the upper case off quickly. The case is attached to the logic board via a ribbon cable.

Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case (there are some hidden plastic clips that need to be clicked off).

Step 10

  • Disconnect the trackpad and keyboard ribbon cable from the logic board, removing tape as necessary.
  • Remove the upper case.

Disconnect the trackpad and keyboard ribbon cable from the logic board, removing tape as necessary.

Remove the upper case.

Step 11

              Left Ambient Light Sensor
  • Disconnect the left ambient light sensor cable from the logic board by placing a spudger beneath the cable and lifting up.

Disconnect the left ambient light sensor cable from the logic board by placing a spudger beneath the cable and lifting up.

Step 12

  • Peel up the left ambient light sensor cable from above the left fan, removing tape as necessary.

Peel up the left ambient light sensor cable from above the left fan, removing tape as necessary.

Step 13

  • Remove the single silver Phillips screw securing the clear plastic shield over the left ambient light sensor.
  • Lift the clear plastic shield off the left ambient light sensor.

Remove the single silver Phillips screw securing the clear plastic shield over the left ambient light sensor.

Lift the clear plastic shield off the left ambient light sensor.

Step 14

  • Use a spudger to pry the left ambient light sensor board out of its housing on the left speaker.
  • Lift the left ambient light sensor board out of the computer.

Use a spudger to pry the left ambient light sensor board out of its housing on the left speaker.

Lift the left ambient light sensor board out of the computer.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                    iRobot

Member since: 09/24/2009

1 Reputation

                                      646 Guides authored                  



                       Badges:
                       36







                                                        +33 more badges