Macbook Pro 15 Core 2 Duo Model A1211 Display Inverter Replacement Repair Guide

Difficulty

Very difficult

Steps

Time Required

Suggest a time??

Sections

Battery
1 step
RAM Shield
2 steps
Upper Case
7 steps
Display Assembly
8 steps
Rear Display Bezel
5 steps
Display Inverter
3 steps

Flags

BackMacBook Pro 15" Core 2 Duo Model A1211
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.

Use your fingers to push both battery release tabs away from the battery, and lift the battery out of the computer.

1024

Step 2

              RAM Shield

Remove the three identical Phillips screws from the memory door.

Remove the three identical Phillips screws from the memory door.

Step 3

Lift the memory door up enough to get a grip on it, and slide it toward you, pulling it away from the casing.

Lift the memory door up enough to get a grip on it, and slide it toward you, pulling it away from the casing.

Step 4

              Upper Case

Remove the two 2.8 mm Phillips screws in the battery compartment near the latch.

Remove the two 2.8 mm Phillips screws in the battery compartment near the latch.

Step 5

Remove the following 6 screws:
Two 10 mm T6 Torx screws on either side of the RAM slot.
Four 14.5 mm Phillips screws along the hinge.

Remove the following 6 screws:

Two 10 mm T6 Torx screws on either side of the RAM slot.

Four 14.5 mm Phillips screws along the hinge.

Step 6

Remove the four 3.2 mm Phillips screws on the port side of the computer.

Remove the four 3.2 mm Phillips screws on the port side of the computer.

Step 7

Rotate the computer 90 degrees and remove the two 3.2 mm Phillips screws from the rear of the computer.

Rotate the computer 90 degrees and remove the two 3.2 mm Phillips screws from the rear of the computer.

Step 8

Rotate the computer 90 degrees again and remove the four 3.2 mm Phillips screws from the side of the computer.

Rotate the computer 90 degrees again and remove the four 3.2 mm Phillips screws from the side of the computer.

Step 9

Do not yank the upper case off quickly. The case is attached to the logic board via a ribbon cable.
Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case (there are some hidden plastic clips that need to be clicked off).

Do not yank the upper case off quickly. The case is attached to the logic board via a ribbon cable.

Lift up at the rear of the case and work your fingers along the sides, freeing the case as you go. Once you have freed the sides, you may need to rock the case up and down to free the front of the upper case (there are some hidden plastic clips that need to be clicked off).

Step 10

Disconnect the trackpad and keyboard ribbon cable from the logic board, removing tape as necessary.
Remove the upper case.

Disconnect the trackpad and keyboard ribbon cable from the logic board, removing tape as necessary.

Remove the upper case.

Step 11

              Display Assembly

Disconnect the three antenna cables attached to the Airport Extreme card.
Apple was kind enough to include a label showing where each color antenna cable plugs in - just make sure to look at this when reconnecting the antenna cables.

Disconnect the three antenna cables attached to the Airport Extreme card.

Apple was kind enough to include a label showing where each color antenna cable plugs in - just make sure to look at this when reconnecting the antenna cables.

Step 12

Deroute the Airport antenna cables from their channel in the left speaker.

Deroute the Airport antenna cables from their channel in the left speaker.

Step 13

Disconnect the iSight cable from the logic board by sliding the cable to the left and out of its connector.

Disconnect the iSight cable from the logic board by sliding the cable to the left and out of its connector.

Step 14

Disconnect the inverter cable from the logic board by placing a spudger beneath the cable and lifting up.

Disconnect the inverter cable from the logic board by placing a spudger beneath the cable and lifting up.

Step 15

Disconnect the display data cable from the logic board by pulling sideways.

Disconnect the display data cable from the logic board by pulling sideways.

Step 16

Remove the silver T6 Torx securing the ground loop in the display data cable to the casing.

Remove the silver T6 Torx securing the ground loop in the display data cable to the casing.

Step 17

Support the display with one hand while removing the following 3 screws:
Two 9.5 mm silver T6 Torx screws with threads on only part of the shaft on the inside of the display hinges.
One 9.5 mm silver T6 Torx screw with threads on the entire shaft on the outside of the left hinge.

Support the display with one hand while removing the following 3 screws:

Two 9.5 mm silver T6 Torx screws with threads on only part of the shaft on the inside of the display hinges.

One 9.5 mm silver T6 Torx screw with threads on the entire shaft on the outside of the left hinge.

Step 18

Grasp the display assembly on both sides and lift it up and out of the computer.

Grasp the display assembly on both sides and lift it up and out of the computer.

Step 19

              Rear Display Bezel

Remove the two 5 mm Phillips screws from the lower left and right corners of the display (two screws total).

Remove the two 5 mm Phillips screws from the lower left and right corners of the display (two screws total).

Step 20

Insert the flat end of a spudger perpendicular to the face of the display between the plastic strip attached to the rear bezel and the front bezel.
Do not insert your spudger between the plastic strip and the rear bezel.
With the spudger still inserted, rotate it away from the display to separate the front and rear bezels.
Work along the left edge of the display until the rear bezel is evenly separated from the front bezel.

Insert the flat end of a spudger perpendicular to the face of the display between the plastic strip attached to the rear bezel and the front bezel.

Do not insert your spudger between the plastic strip and the rear bezel.

With the spudger still inserted, rotate it away from the display to separate the front and rear bezels.

Work along the left edge of the display until the rear bezel is evenly separated from the front bezel.

Step 21

Insert the flat end of a spudger perpendicular to the face of the display between the plastic strip attached to the rear bezel and the front bezel.
With the spudger still inserted, rotate it away from the display to separate the front and rear bezels.
Work along the right edge of the display until the rear bezel is evenly separated from the front bezel.

Work along the right edge of the display until the rear bezel is evenly separated from the front bezel.

Step 22

Insert the flat end of a spudger between the front bezel and the plastic strip attached to the rear bezel near the screw holes at the bottom corners of the display.
Rotate your spudger toward the rear bezel to separate it from the front bezel.
If necessary, enlarge the gap between the lower edge of the rear bezel and the clutch cover until the two components are completely separated.

Insert the flat end of a spudger between the front bezel and the plastic strip attached to the rear bezel near the screw holes at the bottom corners of the display.

Rotate your spudger toward the rear bezel to separate it from the front bezel.

If necessary, enlarge the gap between the lower edge of the rear bezel and the clutch cover until the two components are completely separated.

Step 23

Lift the rear bezel by its bottom edge and rotate it away from the display assembly to separate the top edge.
Remove the rear display bezel from the display assembly.

Lift the rear bezel by its bottom edge and rotate it away from the display assembly to separate the top edge.

Remove the rear display bezel from the display assembly.

Step 24

              Display Inverter

The display inverter is a very thin and delicate circuit board that is easily broken. Use caution when handling.
Carefully lift the inverter board out of the clutch cover.

The display inverter is a very thin and delicate circuit board that is easily broken. Use caution when handling.

Carefully lift the inverter board out of the clutch cover.

Step 25

Disconnect the LCD backlight from the inverter by pulling its connector away from the inverter board.

Disconnect the LCD backlight from the inverter by pulling its connector away from the inverter board.

Step 26

Be cautious to not put any strain on the inverter cable ground loop, as it is a very thin and delicate wire.
Disconnect the inverter cable by pulling its connector away from the socket on the inverter.

Be cautious to not put any strain on the inverter cable ground loop, as it is a very thin and delicate wire.

Disconnect the inverter cable by pulling its connector away from the socket on the inverter.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      19 other people completed this guide.

Author

                                      with 1 other contributor

                    Ben Eisenman

87,459 Reputation

                                      59 Guides authored                  



                       Badges:
                       52







                                                        +49 more badges

Introduction#

What you need#

Introduction

What you need