Difficulty
Moderate
Steps
18
Time Required
45 minutes
Sections
4
- Lower Case
- 2 steps
- Battery Connection
- 2 steps
- Optical Drive
- 11 steps
- Right Speaker/Subwoofer
- 3 steps
Flags
0
BackMacBook Pro 13" Unibody Mid 2012
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Lower Case
- Remove the following ten screws:
- Three 14.4 mm Phillips #00 screws
- Three 3.5 mm Phillips #00 screws
- Four 3.5 mm shouldered Phillips #00 screws
- When replacing the small screws, align them perpendicular to the slight curvature of the case (they don’t go straight down).
Remove the following ten screws:
Three 14.4 mm Phillips #00 screws
Three 3.5 mm Phillips #00 screws
Four 3.5 mm shouldered Phillips #00 screws
When replacing the small screws, align them perpendicular to the slight curvature of the case (they don’t go straight down).
1024
Step 2
- Use your fingers to pry the lower case away from the body of the MacBook near the vent.
- Remove the lower case.
Use your fingers to pry the lower case away from the body of the MacBook near the vent.
Remove the lower case.
Step 3
Battery Connection
- Use the edge of a spudger to pry the battery connector upwards from its socket on the logic board.
- It is useful to pry upward on both short sides of the connector to “walk” it out of its socket. Be careful with the corners of the connectors, they can be easily broken off.
Use the edge of a spudger to pry the battery connector upwards from its socket on the logic board.
It is useful to pry upward on both short sides of the connector to “walk” it out of its socket. Be careful with the corners of the connectors, they can be easily broken off.
Step 4
- Bend the battery cable slightly away from its socket on the logic board so it does not accidentally connect itself while you work.
Bend the battery cable slightly away from its socket on the logic board so it does not accidentally connect itself while you work.
Step 5
Optical Drive
- Use the flat end of a spudger to pry the AirPort/Bluetooth ribbon cable connector up from its socket on the logic board.
Use the flat end of a spudger to pry the AirPort/Bluetooth ribbon cable connector up from its socket on the logic board.
Step 6
Carefully pull the camera cable out of its socket on the logic board.
Pull the cable parallel to the face of the logic board. Pulling it upward may damage the logic board or the cable itself.
Step 7
- Carefully move the AirPort/Bluetooth ribbon cable out of the way as you peel the camera cable off the adhesive securing it to the subwoofer and the AirPort/Bluetooth bracket.
- De-route the camera cable out from under the retaining finger molded into the AirPort/Bluetooth bracket.
Carefully move the AirPort/Bluetooth ribbon cable out of the way as you peel the camera cable off the adhesive securing it to the subwoofer and the AirPort/Bluetooth bracket.
De-route the camera cable out from under the retaining finger molded into the AirPort/Bluetooth bracket.
Step 8
- Use the tip of a spudger to pry the antenna connector closest to the logic board up from its socket on the AirPort/Bluetooth board.
- De-route the antenna cable from under the finger molded into the AirPort/Bluetooth bracket.
Use the tip of a spudger to pry the antenna connector closest to the logic board up from its socket on the AirPort/Bluetooth board.
De-route the antenna cable from under the finger molded into the AirPort/Bluetooth bracket.
Step 9
- Remove the following five screws:
- Two 10.3 mm Phillips screws
- Two 3.1 mm Phillips screws
- One 5 mm Phillips screw
Remove the following five screws:
Two 10.3 mm Phillips screws
Two 3.1 mm Phillips screws
One 5 mm Phillips screw
Step 10
- Pull the AirPort/Bluetooth assembly and the Subwoofer upward near the center of the side of the optical drive until they clear each other.
- Move the AirPort/Bluetooth assembly and the subwoofer away from the top of the optical drive.
Pull the AirPort/Bluetooth assembly and the Subwoofer upward near the center of the side of the optical drive until they clear each other.
Move the AirPort/Bluetooth assembly and the subwoofer away from the top of the optical drive.
Step 11
- Pull the right speaker/subwoofer cable out from under the retaining finger near the side of the optical drive.
- Pull the right speaker/subwoofer cable upward to disconnect it from the logic board.
Pull the right speaker/subwoofer cable out from under the retaining finger near the side of the optical drive.
Pull the right speaker/subwoofer cable upward to disconnect it from the logic board.
Step 12
- Use the flat end of a spudger to pry the hard drive cable connector up from its socket on the logic board.
- Bend the hard drive cable away from the optical drive.
Use the flat end of a spudger to pry the hard drive cable connector up from its socket on the logic board.
Bend the hard drive cable away from the optical drive.
Step 13
- Use the flat end of a spudger to pry the optical drive connector up from its socket on the logic board.
Use the flat end of a spudger to pry the optical drive connector up from its socket on the logic board.
Step 14
- Remove the three 2.7 mm Phillips screws securing the optical drive to the upper case.
Remove the three 2.7 mm Phillips screws securing the optical drive to the upper case.
Step 15
- Pull the optical drive upward from its edge closest to the display and remove it from the upper case.
Pull the optical drive upward from its edge closest to the display and remove it from the upper case.
Step 16
Right Speaker/Subwoofer
- Use a plastic opening tool or another thin prying object to carefully pry the right speaker up from the adhesive securing it to the upper case.
- Start prying up from the edge of the right speaker nearest the display. Starting from the other side may damage one of the antennas.
- Pry up along the edge of the right speaker until it is separated from the upper case.
Use a plastic opening tool or another thin prying object to carefully pry the right speaker up from the adhesive securing it to the upper case.
Start prying up from the edge of the right speaker nearest the display. Starting from the other side may damage one of the antennas.
Pry up along the edge of the right speaker until it is separated from the upper case.
Step 17
- Pull the right speaker away from the optical drive opening.
Pull the right speaker away from the optical drive opening.
Step 18
- Peel up the right speaker cable along the edge of the optical drive opening.
- De-route the cable from the clips near the edge of the logic board.
- Remove the right speaker/subwoofer assembly from the upper case.
Peel up the right speaker cable along the edge of the optical drive opening.
De-route the cable from the clips near the edge of the logic board.
Remove the right speaker/subwoofer assembly from the upper case.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
49 other people completed this guide.
Author
with 3 other contributors
Andrew Optimus Goldheart
Member since: 10/17/2009
491,689 Reputation
411 Guides authored
Badges:
44
+41 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,767 Guides authored
Bru Nelle - Nov 30, 2020
Reply
Do you recommend any brand of speakers for macbook pro replacement ?
Sam Omiotek - May 6, 2021
Our parts are tested by our parts testing department and come with a warranty. If anything you buy from us does not work, customer service will make it right.
MacBook Pro 13" Unibody (Early 2011-Mid 2012) Subwoofer and Right Speaker
Randy Allen - Dec 18, 2022
Reply
Is there no left speaker? I can only find purchase for right speaker. Sorry I’m a newbie lol. Thank you!