Featured
Featured Guide
Difficulty
Easy
Steps
6
Time Required
15 - 30 minutes
Sections
3
- Lower Case
- 2 steps
- Battery Connection
- 2 steps
- RAM
- 2 steps
Flags
1
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
BackMacBook Pro 13" Unibody Mid 2012
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Lower Case
- Remove the following ten screws:
- Three 14.4 mm Phillips #00 screws
- Three 3.5 mm Phillips #00 screws
- Four 3.5 mm shouldered Phillips #00 screws
- When replacing the small screws, align them perpendicular to the slight curvature of the case (they don’t go straight down).
Remove the following ten screws:
Three 14.4 mm Phillips #00 screws
Three 3.5 mm Phillips #00 screws
Four 3.5 mm shouldered Phillips #00 screws
When replacing the small screws, align them perpendicular to the slight curvature of the case (they don’t go straight down).
1024
Step 2
- Use your fingers to pry the lower case away from the body of the MacBook near the vent.
- Remove the lower case.
Use your fingers to pry the lower case away from the body of the MacBook near the vent.
Remove the lower case.
Step 3
Battery Connection
- Use the edge of a spudger to pry the battery connector upwards from its socket on the logic board.
- It is useful to pry upward on both short sides of the connector to “walk” it out of its socket. Be careful with the corners of the connectors, they can be easily broken off.
Use the edge of a spudger to pry the battery connector upwards from its socket on the logic board.
It is useful to pry upward on both short sides of the connector to “walk” it out of its socket. Be careful with the corners of the connectors, they can be easily broken off.
Step 4
- Bend the battery cable slightly away from its socket on the logic board so it does not accidentally connect itself while you work.
Bend the battery cable slightly away from its socket on the logic board so it does not accidentally connect itself while you work.
Step 5
RAM
- Pull the two RAM retaining arms away from the center of the RAM chip.
- The RAM chip should “pop” up slightly from its socket.
Pull the two RAM retaining arms away from the center of the RAM chip.
The RAM chip should “pop” up slightly from its socket.
Step 6
- Pull the RAM stick out of its socket.
- Repeat this process to remove the second RAM chip.
Pull the RAM stick out of its socket.
Repeat this process to remove the second RAM chip.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
571 other people completed this guide.
Author
with 4 other contributors
Andrew Optimus Goldheart
Member since: 10/17/2009
491,686 Reputation
411 Guides authored
Badges:
44
+41 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,767 Guides authored
nix - Dec 26, 2012
Reply
My mid-2012 2.5 i5 works perfectly with 16 Gb of 1600Mhz DDR3.
Michael Chandler - Feb 1, 2014
Just replaced my 4GB with 16GB of PNY from Best Buy. AWESOME difference in performance!!
Lin - Nov 18, 2014
Could you please specify the memory chip that you bought? I need more details in order to get the right one, thanks!
Seji the veggie - Aug 3, 2015
Any memory kit that is either validated by Apple or that has the proper channel configuration (9-9-9-24) is okay to use. If you are looking for pure performance RAM, a kit of Corsair Vengeance RAM is okay to use (again, check the channel configuration), but most people will benefit from a kit of Corsair Mac Memory or the kit that iFixit provides in the volume of your choice.
robinprior - Jun 23, 2020