Macbook Pro 13 Unibody Early 2011 Trackpad Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 - 40 minutes

Sections

Lower Case
2 steps
Battery Connection
2 steps
Battery
3 steps
Trackpad
6 steps

Flags

BackMacBook Pro 13" Unibody Early 2011
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Lower Case

Remove the following ten screws:
Three 14.4 mm Phillips #00 screws
Three 3.5 mm Phillips #00 screws
Four 3.5 mm shouldered Phillips #00 screws
When replacing the small screws, align them perpendicular to the slight curvature of the case (they don’t go straight down).

Remove the following ten screws:

Three 14.4 mm Phillips #00 screws

Three 3.5 mm Phillips #00 screws

Four 3.5 mm shouldered Phillips #00 screws

When replacing the small screws, align them perpendicular to the slight curvature of the case (they don’t go straight down).

1024

Step 2

Use your fingers to pry the lower case away from the body of the MacBook near the vent.
Remove the lower case.

Use your fingers to pry the lower case away from the body of the MacBook near the vent.

Remove the lower case.

Step 3

              Battery Connection

Use the edge of a spudger to pry the battery connector upwards from its socket on the logic board.
It is useful to pry upward on both short sides of the connector to “walk” it out of its socket. Be careful with the corners of the connectors, they can be easily broken off.

Use the edge of a spudger to pry the battery connector upwards from its socket on the logic board.

It is useful to pry upward on both short sides of the connector to “walk” it out of its socket. Be careful with the corners of the connectors, they can be easily broken off.

Step 4

Bend the battery cable slightly away from its socket on the logic board so it does not accidentally connect itself while you work.

Bend the battery cable slightly away from its socket on the logic board so it does not accidentally connect itself while you work.

Step 5

              Battery

Remove the following two screws:
One 5.6 mm Tri-point screw
One 13 mm Tri-point screw

Remove the following two screws:

One 5.6 mm Tri-point screw

One 13 mm Tri-point screw

Step 6

Carefully peel the battery warning label off the upper case between the battery and the optical drive.
Do not remove the label from the battery.

Carefully peel the battery warning label off the upper case between the battery and the optical drive.

Do not remove the label from the battery.

Step 7

Use the attached plastic pull tab to remove the battery from the upper case.
If you’re installing a new battery, you should calibrate it after installation:
Charge it to 100%, and then keep charging it for at least 2 more hours. Next, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.
If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook’s SMC.

Use the attached plastic pull tab to remove the battery from the upper case.

If you’re installing a new battery, you should calibrate it after installation:

Charge it to 100%, and then keep charging it for at least 2 more hours. Next, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.

If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook’s SMC.

Step 8

              Trackpad

Use the flat end of a spudger to carefully pry the trackpad connector up from its socket on the logic board.

Use the flat end of a spudger to carefully pry the trackpad connector up from its socket on the logic board.

Step 9

Open your MacBook Pro and set it on a table as shown.

Open your MacBook Pro and set it on a table as shown.

Step 10

While holding the edge of the trackpad closest to the logic board with one hand, remove the four 1.2 mm Phillips screws highlighted in red.

While holding the edge of the trackpad closest to the logic board with one hand, remove the four 1.2 mm Phillips screws highlighted in red.

Step 11

If necessary, carefully dislodge the edge of the trackpad closest to the keyboard from its recess in the upper case by pushing it away from the brackets attached to the upper case.
Carefully push the trackpad connector and cable down through the slot cut into the upper case.
It may be necessary to use a spudger to help get the trackpad connector past the edge of the logic board.
Once the cable has been completely pulled through its slot in the upper case, pull the trackpad away from the outer edge of the upper case and remove it from the machine.

If necessary, carefully dislodge the edge of the trackpad closest to the keyboard from its recess in the upper case by pushing it away from the brackets attached to the upper case.

Carefully push the trackpad connector and cable down through the slot cut into the upper case.

It may be necessary to use a spudger to help get the trackpad connector past the edge of the logic board.

Once the cable has been completely pulled through its slot in the upper case, pull the trackpad away from the outer edge of the upper case and remove it from the machine.

Step 12

If you are installing a replacement trackpad that didn’t come with the attached flex cable, you’ll need to use the cable from your old trackpad.
To remove the flex cable from the old trackpad, first flip open the latch on the ZIF connector, opposite the cable. Then, apply a little heat from a hair dryer or iOpener to soften the adhesive securing the cable to the trackpad, and carefully peel off and remove the cable.
When installing your new trackpad, routing the cable through the upper case and past the logic board may be difficult. It is helpful to use the tip of a spudger to guide the connector past the logic board while pushing the cable through its slot in the upper case with your other hand.

If you are installing a replacement trackpad that didn’t come with the attached flex cable, you’ll need to use the cable from your old trackpad.

To remove the flex cable from the old trackpad, first flip open the latch on the ZIF connector, opposite the cable. Then, apply a little heat from a hair dryer or iOpener to soften the adhesive securing the cable to the trackpad, and carefully peel off and remove the cable.

When installing your new trackpad, routing the cable through the upper case and past the logic board may be difficult. It is helpful to use the tip of a spudger to guide the connector past the logic board while pushing the cable through its slot in the upper case with your other hand.

Step 13

Next, reinstall the four 1.2 mm Phillips screws along the inner edge of the trackpad.
Tighten the screws all the way, then back them out about 1/4 turn.
Check the alignment of the trackpad on the keyboard side of the upper case. Once you have centered the trackpad in the upper case, tighten the four Phillips screws all the way.

Next, reinstall the four 1.2 mm Phillips screws along the inner edge of the trackpad.

Tighten the screws all the way, then back them out about 1/4 turn.

Check the alignment of the trackpad on the keyboard side of the upper case. Once you have centered the trackpad in the upper case, tighten the four Phillips screws all the way.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      162 other people completed this guide.

Author

                                      with 4 other contributors

                    Andrew Bookholt

575,478 Reputation

                                      618 Guides authored                  



                       Badges:
                       47







                                                        +44 more badges

rebeccanorris - Jun 23, 2015

I couldn’t be more pleased with myself or ifixit right now. I went to the Apple service centre to find out about getting my trackpad fixed and was told it would take 2 weeks to diagnose what the problem was and up to another 2 weeks before they could fix it. Luckily, I stumbled upon ifixit - got a tool pack and parts delivered in 5 days and I was just able to replace the trackpad easily in 30 minutes. I did find that I wasn’t able to get the screws from the back of the trackpad out with the Phillips 00 screwdriver though - I had to use the 000. I am weirdly looking forward to something else breaking now just so I can fix it:-)

Omkar Danke - Jul 12, 2016

Why did I not do this earlier! I wasted 2 years of my laptop life struggling with the trackpad and external mouses. This was pretty easy.

Judy MacDonald - May 1, 2017

Just installed my new trackpad and it works like a dream. Thanks!!

patrisha.wells - May 15, 2017

Thanks!! This worked perfectly. (Almost… I stripped a couple tiny screws on the trackpad before it was perfectly placed so I have a dead spot about the size of a quarter in the upper right corner where it won’t click, but it’s much better than the previous one.)

Rachel Wilkosz - Jul 20, 2017

I was scared to this project until I found this site! I’ve never opened up any of my computers until now and this manual made it so easy!

Introduction#

What you need#

Introduction

What you need