Macbook Pro 13 Retina Display Early 2013 Battery Contact Board Replacement Repair Guide

Difficulty

Moderate

Steps

9

Time Required

                          10 - 20 minutes            

Sections

3

• Lower Case
• 3 steps
• Battery Connector
• 5 steps
• Battery Contact Board
• 1 step

Flags

0

• BackMacBook Pro 13" Retina Display Early 2013

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Lower Case               

• Remove the following ten screws securing the lower case to the upper case:
• Two 2.3 mm P5 Pentalobe screws
• Eight 3.0 mm P5 Pentalobe screws
• Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your device.

Remove the following ten screws securing the lower case to the upper case:

Two 2.3 mm P5 Pentalobe screws

Eight 3.0 mm P5 Pentalobe screws

Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your device.

1024

Step 2

• Wedge your fingers between the upper case and the lower case.
• Gently pull the lower case away from the upper case.
• Remove the lower case and set it aside.

Wedge your fingers between the upper case and the lower case.

Gently pull the lower case away from the upper case.

Remove the lower case and set it aside.

Step 3

• During reassembly, gently push down the center of the lower case to reattach the two plastic clips.
• The lower case is connected to the upper case at the center, with two plastic clips.

During reassembly, gently push down the center of the lower case to reattach the two plastic clips.

The lower case is connected to the upper case at the center, with two plastic clips.

Step 4

              Battery Connector               

• Remove the plastic cover adhered to the battery contact board.

Remove the plastic cover adhered to the battery contact board.

Step 5

• Remove the following screws securing the battery connector board to the logic board:
• Two 2.8 mm T6 Torx screws
• One 7.0 mm T6 Torx shouldered screw

Remove the following screws securing the battery connector board to the logic board:

Two 2.8 mm T6 Torx screws

One 7.0 mm T6 Torx shouldered screw

Step 6

• Use tweezers to remove the small plastic cover located near the bottom right of the battery connector board.

Use tweezers to remove the small plastic cover located near the bottom right of the battery connector board.

Step 7

• Remove the wide head 6.4 mm T6 Torx screw securing the battery connector to the logic board assembly.

Remove the wide head 6.4 mm T6 Torx screw securing the battery connector to the logic board assembly.

Step 8

• Carefully lift the battery connector board up off the logic board.
• It is recommended to bend the battery cables just slightly, to keep the board suspended up above the logic board and out of the way.
• Do not fold the board completely over, or crease the cables, as this may damage the battery.

Carefully lift the battery connector board up off the logic board.

It is recommended to bend the battery cables just slightly, to keep the board suspended up above the logic board and out of the way.

Do not fold the board completely over, or crease the cables, as this may damage the battery.

Step 9

              Battery Contact Board               

• Grasp the Interposer with tweezers.
• An interposer is the name for an interface that links one electrical connection to another. In this repair, it is the board connecting the battery to logic board.
• Lift the Interposer off the logic board and remove it.
• Removing this board will ensure that the battery remains disconnected throughout your repair, preventing your computer from accidentally powering on. It’s also a good idea to take it out so it doesn’t fall out unexpectedly.

Grasp the Interposer with tweezers.

An interposer is the name for an interface that links one electrical connection to another. In this repair, it is the board connecting the battery to logic board.

Lift the Interposer off the logic board and remove it.

Removing this board will ensure that the battery remains disconnected throughout your repair, preventing your computer from accidentally powering on. It’s also a good idea to take it out so it doesn’t fall out unexpectedly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.                                             

Author

                                      with 4 other contributors 

                    Sam Goldheart                     

Member since: 10/18/2012

455,549 Reputation

                                      548 Guides authored                  



                       Badges:
                       48







                                                        +45 more badges                           

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,767 Guides authored