Macbook Pro 13 Four Thunderbolt Ports 2020 Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 - 2 hours

Sections

Lower Case
7 steps
Battery Disconnect
7 steps
Antenna Bar Assembly
11 steps
Screen
4 steps

Flags

BackMacBook Pro 13" Four Thunderbolt Ports 2020
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

For your safety, drain your MacBook Pro’s battery below 25% charge before you begin.

Note: Some Torx T3 screws may require a Torx T4 bit to avoid stripping.

Note: After installing a replacement display, your True Tone may not function normally.

Some photos in this guide are from a different model and may contain slight visual discrepancies, but they won’t affect the guide procedure.

What you need

Step 1

              Remove the pentalobe screws

Before starting this procedure, you should disable your Mac’s Auto Boot feature. Auto Boot powers on your Mac when you open the lid, and may be accidentally triggered during disassembly. Use this guide to disable Auto Boot.
If your MacBook is running Big Sur v11.1 or later, disabling Auto Boot may not work. You can proceed normally, but make sure to disconnect the battery as soon as you’re inside.
Completely power off and unplug your MacBook before you start. Close the display and flip the entire laptop upside-down.
Use a P5 Pentalobe driver to remove the six screws securing the lower case:
Two 6.7 mm screws
Four 3.4 mm screws
Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your device.

Before starting this procedure, you should disable your Mac’s Auto Boot feature. Auto Boot powers on your Mac when you open the lid, and may be accidentally triggered during disassembly. Use this guide to disable Auto Boot.

If your MacBook is running Big Sur v11.1 or later, disabling Auto Boot may not work. You can proceed normally, but make sure to disconnect the battery as soon as you’re inside.

Completely power off and unplug your MacBook before you start. Close the display and flip the entire laptop upside-down.

Use a P5 Pentalobe driver to remove the six screws securing the lower case:

Two 6.7 mm screws

Four 3.4 mm screws

Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your device.

1024

Step 2

              Open a gap using a suction cup

Apply a suction handle to the lower case near the front-center area of the MacBook Pro.
Lift the suction handle to create a slight gap between the lower case and the chassis.

Apply a suction handle to the lower case near the front-center area of the MacBook Pro.

Lift the suction handle to create a slight gap between the lower case and the chassis.

Step 3

              Separate the clips

Insert one corner of an opening pick into the space between the lower case and the chassis.
Slide the opening pick around the nearest corner and halfway up the side of the case.
This releases the first of the hidden clips securing the lower case to the chassis. You should feel and hear the clip pop free.

Insert one corner of an opening pick into the space between the lower case and the chassis.

Slide the opening pick around the nearest corner and halfway up the side of the case.

This releases the first of the hidden clips securing the lower case to the chassis. You should feel and hear the clip pop free.

Step 4

Repeat the previous step on the opposite side, sliding your opening pick under the lower case and up the side to pop the second clip free.

Repeat the previous step on the opposite side, sliding your opening pick under the lower case and up the side to pop the second clip free.

Step 5

Insert your opening pick once again under the front edge of the lower case, near one of the two centermost screw holes.
Give the pick a firm twist to pop free the third clip securing the lower case to the chassis.
Repeat this procedure near the other of the two centermost screw holes, popping the fourth clip free.

Insert your opening pick once again under the front edge of the lower case, near one of the two centermost screw holes.

Give the pick a firm twist to pop free the third clip securing the lower case to the chassis.

Repeat this procedure near the other of the two centermost screw holes, popping the fourth clip free.

Step 6

Pull the lower case firmly towards the front of the MacBook (away from the hinge area) to separate the last of the clips securing the lower case.
Pull first at one corner, then the other.
Pull to the side—not up.
This can require a lot of force.

Pull the lower case firmly towards the front of the MacBook (away from the hinge area) to separate the last of the clips securing the lower case.

Pull first at one corner, then the other.

Pull to the side—not up.

This can require a lot of force.

Step 7

              Remove the lower case

Remove the lower case.
To reinstall the lower case:
Set it in place and align the sliding clips near the display hinge. Press down and slide the cover toward the hinge. It should stop sliding as the clips engage.
When the sliding clips are fully engaged and the lower case looks correctly aligned, press down firmly on the lower case to engage the four hidden clips underneath. You should feel and hear them snap into place.

Remove the lower case.

To reinstall the lower case:

Set it in place and align the sliding clips near the display hinge. Press down and slide the cover toward the hinge. It should stop sliding as the clips engage.

When the sliding clips are fully engaged and the lower case looks correctly aligned, press down firmly on the lower case to engage the four hidden clips underneath. You should feel and hear them snap into place.

Step 8

              Uncover the battery connector

Carefully peel up the large piece of tape covering the battery connector, on the edge of the logic board nearest the battery.
Remove the tape.

Carefully peel up the large piece of tape covering the battery connector, on the edge of the logic board nearest the battery.

Remove the tape.

Step 9

Gently peel back the small piece of tape covering the battery board data cable connector.
The tape is integrated into the ribbon cable and will not detach completely. Simply peel it back enough to access the connector.

Gently peel back the small piece of tape covering the battery board data cable connector.

The tape is integrated into the ribbon cable and will not detach completely. Simply peel it back enough to access the connector.

Step 10

Use the tip of a spudger to flip up the small black locking tab securing the cable in its connector.

Use the tip of a spudger to flip up the small black locking tab securing the cable in its connector.

Step 11

Disconnect the battery board data cable by sliding it out from its socket.
Slide parallel to the logic board, in the direction of the cable.

Disconnect the battery board data cable by sliding it out from its socket.

Slide parallel to the logic board, in the direction of the cable.

Step 12

Fold the battery board data cable to the side and out of the way.

Fold the battery board data cable to the side and out of the way.

Step 13

Use a T5 Torx driver to remove the 3.7 mm pancake screw securing the battery power connector.

Use a T5 Torx driver to remove the 3.7 mm pancake screw securing the battery power connector.

Step 14

              Disconnect the battery

Use a spudger to gently lift the battery power connector, disconnecting the battery.
Lift the connector high enough so that it stays separated from its socket. If it accidentally makes contact during the course of your repair, it could damage your MacBook Pro.

Use a spudger to gently lift the battery power connector, disconnecting the battery.

Lift the connector high enough so that it stays separated from its socket. If it accidentally makes contact during the course of your repair, it could damage your MacBook Pro.

Step 15

              Remove the hinge covers

Use a T3 Torx driver to remove the four 1.9 mm screws securing the plastic covers on top of the display hinges.
Remove both plastic hinge covers.

Use a T3 Torx driver to remove the four 1.9 mm screws securing the plastic covers on top of the display hinges.

Remove both plastic hinge covers.

Step 16

              Disconnect the main display cable

Remove the two 2.9 mm T3 Torx screws securing the aluminum cover on top of the main display cable.
Remove the cover.

Remove the two 2.9 mm T3 Torx screws securing the aluminum cover on top of the main display cable.

Remove the cover.

Step 17

Remove the two 1.7 mm T3 Torx screws securing the aluminum cover on top of the display cable flex connector.
Remove the cover.

Remove the two 1.7 mm T3 Torx screws securing the aluminum cover on top of the display cable flex connector.

Step 18

Pry the display board flex cable straight up from its socket to disconnect it from the display board.

Pry the display board flex cable straight up from its socket to disconnect it from the display board.

Step 19

              Unscrew the antenna cable assembly

Remove the four 1.5 mm T3 Torx screws securing the two aluminum covers on top of the two display board cables.
Use a pair of tweezers to remove the two aluminium covers.

Remove the four 1.5 mm T3 Torx screws securing the two aluminum covers on top of the two display board cables.

Use a pair of tweezers to remove the two aluminium covers.

Step 20

Remove the four 3.9 mm T5 Torx screws (two from each side) securing the antenna cable assembly.
Also remove the twelve 1.1 mm P2 pentalobe screws (six from each side).

Remove the four 3.9 mm T5 Torx screws (two from each side) securing the antenna cable assembly.

Also remove the twelve 1.1 mm P2 pentalobe screws (six from each side).

Step 21

              Disconnect the antenna cables

Carefully disconnect the three antenna coax cables by prying them straight up from the logic board.
Slide your tweezers or the pointed end of your spudger underneath each cable until it’s near the socket, and then gently twist or pry up to disconnect it.
To reconnect each cable, align the connector directly over its socket, and then press down so it snaps into place.

Carefully disconnect the three antenna coax cables by prying them straight up from the logic board.

Slide your tweezers or the pointed end of your spudger underneath each cable until it’s near the socket, and then gently twist or pry up to disconnect it.

To reconnect each cable, align the connector directly over its socket, and then press down so it snaps into place.

Step 22

Remove the 2.8 mm T5 Torx screw securing the three antenna coax cables to the main board.

Remove the 2.8 mm T5 Torx screw securing the three antenna coax cables to the main board.

Step 23

              Pry up the antenna cable assembly

Use an opening pick to lever out the antenna cable assembly in the areas shown.
Don’t slide the opening pick from side to side, as there are two display cables that could be damaged in the way.

Use an opening pick to lever out the antenna cable assembly in the areas shown.

Don’t slide the opening pick from side to side, as there are two display cables that could be damaged in the way.

Step 24

              Remove the antenna assembly

Carefully remove the antenna assembly, while simultaneously feeding the antenna cable bundle out from underneath the heat pipe.

Carefully remove the antenna assembly, while simultaneously feeding the antenna cable bundle out from underneath the heat pipe.

Step 25

Remove the antenna cable assembly.
During reassembly, gently pinch the cable bundle together and guide it under the heat pipe into the correct position on the board. If needed, use your tools to help guide it through, but don’t force it.

Remove the antenna cable assembly.

During reassembly, gently pinch the cable bundle together and guide it under the heat pipe into the correct position on the board. If needed, use your tools to help guide it through, but don’t force it.

Step 26

              Unscrew the display cable assembly

Remove the four 3.9 mm T3 Torx screws securing the two display cable cover springs.

Remove the four 3.9 mm T3 Torx screws securing the two display cable cover springs.

Step 27

              Remove the display cable assembly

Grab the left side of the display cable assembly and pull it towards the bottom end of the MacBook and away from the cover spring.
Use a pair of tweezers to pull the cover spring of the display cable out of its recess.
Repeat this step with the right cover spring of the display cable assembly.

Grab the left side of the display cable assembly and pull it towards the bottom end of the MacBook and away from the cover spring.

Use a pair of tweezers to pull the cover spring of the display cable out of its recess.

Repeat this step with the right cover spring of the display cable assembly.

Step 28

              Unscrew the hinge bolts

Fully open the screen and stand your MacBook Pro up on one side.
While steadying the MacBook pro with your free hand, remove the three T8 Torx screws from the lower display hinge.
Remove the remaining three T8 Torx screws from the upper display bracket.

Fully open the screen and stand your MacBook Pro up on one side.

While steadying the MacBook pro with your free hand, remove the three T8 Torx screws from the lower display hinge.

Remove the remaining three T8 Torx screws from the upper display bracket.

Step 29

              Remove the screen assembly

Keep a firm grip on both the screen and main body of the MacBook Pro. Either half can fall unexpectedly during this step.
Push both halves of the MacBook Pro together so that the hinge brackets can be lifted clear of their recesses in the chassis.
Push the main body of the MacBook Pro away from you while pulling the screen toward you to separate it.
Remove the display/screen assembly, being careful not to snag it on any cables.

Keep a firm grip on both the screen and main body of the MacBook Pro. Either half can fall unexpectedly during this step.

Push both halves of the MacBook Pro together so that the hinge brackets can be lifted clear of their recesses in the chassis.

Push the main body of the MacBook Pro away from you while pulling the screen toward you to separate it.

Remove the display/screen assembly, being careful not to snag it on any cables.

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting or search our Answers community for help.

If you are having True Tone, Touch Bar lighting, or keyboard backlight issues after installing a replacement display, try resetting your Mac’s SMC and NVRAM/PRAM.

Cancel: I did not complete this guide.

                                                                                      11 other people completed this guide.

Author

                    Carsten Frauenheim

Member since: 03/10/2020

81,713 Reputation

                                      330 Guides authored                  



                       Badges:
                       38







                                                        +35 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,772 Guides authored

Harry Yu - Nov 18, 2022

I’m not sure if I just stripped the screws a bit, but for steps 17 and 19 (the display cable covers), a T4 Torx worked better than a T3 Torx for both removing and reinstalling the screws.

Carsten Frauenheim - Nov 18, 2022

Harry, sometimes a T4 driver may fit better into some MacBook T3 screws, but it depends on the specific bit used and the tolerances on the specific screw in the machine. Thanks for your insight—I’ll add a note to the guide!

maccentric - Jan 2, 2023

Just finished doing this and when the computer boots the apple logo looks the correct brightness. Halfway through the boot process, the screen gets really dim, even through brightness is set to max. Not sure the cause of this, will report back if I figure it out.

Introduction#

What you need#

Team#

Introduction

What you need

Team