Macbook Core Duo Hard Drive Connector Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 minutes - 2 hours

Sections

Battery
2 steps
Memory Cover
2 steps
Upper Case
8 steps
Hard Drive Connector
7 steps

Flags

BackMacBook Core Duo
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Use a coin or spudger to rotate the battery-locking screw 90 degrees clockwise.

Use a coin or spudger to rotate the battery-locking screw 90 degrees clockwise.

1024

Step 2

Lift the battery out of the computer.

Lift the battery out of the computer.

Step 3

              Memory Cover

Remove the three evenly-spaced Phillips screws from along the rear wall of the battery compartment.
The screws are captive to the metal memory cover.
When replacing the battery casing, use a spudger to re-insert the foam cushioning behind the rear wall for propper battery spacing.

Remove the three evenly-spaced Phillips screws from along the rear wall of the battery compartment.

The screws are captive to the metal memory cover.

When replacing the battery casing, use a spudger to re-insert the foam cushioning behind the rear wall for propper battery spacing.

Step 4

Lift up on L-shaped memory cover, slide it to the right, and lift it out of the computer.

Lift up on L-shaped memory cover, slide it to the right, and lift it out of the computer.

Step 5

              Upper Case

Remove the following 3 screws:
One 11 mm Phillips #00 in the middle of the case.
Two 14.5 mm Phillips #00.
If the screws stick in the case, you can use a magnetized screwdriver to draw them out.
The shorter of the three screws goes in the middle.

Remove the following 3 screws:

One 11 mm Phillips #00 in the middle of the case.

Two 14.5 mm Phillips #00.

If the screws stick in the case, you can use a magnetized screwdriver to draw them out.

The shorter of the three screws goes in the middle.

Step 6

Remove the following 3 screws from the rear wall of the battery compartment:
Two 3 mm Phillips #00. (A1181 has three 3 mm screws and one 4 mm.)
One 4 mm Phillips #00 on the right side.
When reinstalling these screws, press gently on the lower case to line up the screw holes.
These screws easily strip, so be careful while taking these particular screws out.

Remove the following 3 screws from the rear wall of the battery compartment:

Two 3 mm Phillips #00. (A1181 has three 3 mm screws and one 4 mm.)

One 4 mm Phillips #00 on the right side.

When reinstalling these screws, press gently on the lower case to line up the screw holes.

These screws easily strip, so be careful while taking these particular screws out.

Step 7

Remove the two 6 mm Phillips #00 screws from either side of the right wall of the battery compartment (not the ones closest to the battery connector).

Remove the two 6 mm Phillips #00 screws from either side of the right wall of the battery compartment (not the ones closest to the battery connector).

Step 8

Remove the four 3 mm indicated Phillips #00 screws from the front wall of the battery compartment. When working from the left, remove the 2nd, 4th, 7th and 9th screw.

Remove the four 3 mm indicated Phillips #00 screws from the front wall of the battery compartment. When working from the left, remove the 2nd, 4th, 7th and 9th screw.

Step 9

Remove the following 4 screws from the back of the computer:
Two 7 mm shouldered Phillips on the far sides.
Two 10.5 mm Phillips toward the center.
Do not over-tighten these; you can cause the case to distort.

Remove the following 4 screws from the back of the computer:

Two 7 mm shouldered Phillips on the far sides.

Two 10.5 mm Phillips toward the center.

Do not over-tighten these; you can cause the case to distort.

Step 10

Remove the two 5.2 mm shouldered Phillips #00 screws from the optical side of the computer.
It is not necessary to remove the similar screws on the other side of the computer.

Remove the two 5.2 mm shouldered Phillips #00 screws from the optical side of the computer.

It is not necessary to remove the similar screws on the other side of the computer.

Step 11

Starting near the display and working around to the front of the computer, pry up on the upper case. It is held with clips on the right above the optical drive. These will release with some firm lifting pressure.
Be careful when prying up the upper case. It’s very easy to slice open a fingertip and thus provide the blood sacrifice the Mac gods sometimes require of those who insist on doing their own repairs.
There’s a trackpad and keyboard ribbon connecting the upper case to the logic board, so don’t pull the upper case off entirely just yet.
If you have trouble getting the clips to release, be careful that you are not prying the plastic top of the upper case away from its metal frame.

Starting near the display and working around to the front of the computer, pry up on the upper case. It is held with clips on the right above the optical drive. These will release with some firm lifting pressure.

Be careful when prying up the upper case. It’s very easy to slice open a fingertip and thus provide the blood sacrifice the Mac gods sometimes require of those who insist on doing their own repairs.

There’s a trackpad and keyboard ribbon connecting the upper case to the logic board, so don’t pull the upper case off entirely just yet.

If you have trouble getting the clips to release, be careful that you are not prying the plastic top of the upper case away from its metal frame.

Step 12

While holding up the upper case (from the bottom or the top), use a spudger to pry up the orange trackpad and keyboard cable from its connector.
Take care to pry between the black socket and the white connector. You might have to pry on both sides for it to release properly.
Do not pry from the bottom or the top, but from the sides.
If you happen to break your upper case cable when removing the upper case, we stock the cable individually and we have a guide that makes replacing it easy.

While holding up the upper case (from the bottom or the top), use a spudger to pry up the orange trackpad and keyboard cable from its connector.

Take care to pry between the black socket and the white connector. You might have to pry on both sides for it to release properly.

Do not pry from the bottom or the top, but from the sides.

If you happen to break your upper case cable when removing the upper case, we stock the cable individually and we have a guide that makes replacing it easy.

Step 13

              Hard Drive Connector

Use the white plastic pull-tab to slide the hard drive to the left and out of the computer.

Use the white plastic pull-tab to slide the hard drive to the left and out of the computer.

Step 14

Disconnect the orange optical drive ribbon cable from the logic board.

Disconnect the orange optical drive ribbon cable from the logic board.

Step 15

Disconnect the newly-revealed display data cable. If there is no pull-tab on the top of the connector, it may be helpful to use a spudger to disconnect this connector.

Disconnect the newly-revealed display data cable. If there is no pull-tab on the top of the connector, it may be helpful to use a spudger to disconnect this connector.

Step 16

Disconnect the (once again) newly-revealed hard drive cable.

Disconnect the (once again) newly-revealed hard drive cable.

Step 17

Deroute the hard drive connector cable from the four tabs along the edge of the optical drive.

Deroute the hard drive connector cable from the four tabs along the edge of the optical drive.

Step 18

Remove the two Phillips screws securing the hard drive connector to the lower case.

Remove the two Phillips screws securing the hard drive connector to the lower case.

Step 19

Carefully lift the hard drive connector out of the case slightly, and turn it over to reveal the IR sensor connector beneath. Use a spudger to flip up the tiny bar holding the cable in place.
Slide the orange IR sensor cable out of its connector, and lift the hard drive connector out of the computer.

Carefully lift the hard drive connector out of the case slightly, and turn it over to reveal the IR sensor connector beneath. Use a spudger to flip up the tiny bar holding the cable in place.

Slide the orange IR sensor cable out of its connector, and lift the hard drive connector out of the computer.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      26 other people completed this guide.

Author

                                      with 5 other contributors

                    iRobot

Member since: 09/24/2009

1 Reputation

                                      646 Guides authored                  



                       Badges:
                       36







                                                        +33 more badges

Introduction#

What you need#

Introduction

What you need