Difficulty

Moderate

Steps

10

Time Required

                          10 - 20 minutes

Sections

3

  • Lower Case
  • 2 steps
  • Battery Disconnect
  • 2 steps
  • Antenna Bar
  • 6 steps

Flags

0

  • BackMacBook Air 13" Retina 2019

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Remove the screws securing the lower case
  • Before starting this procedure, you should disable your Mac’s Auto Boot feature. Auto Boot powers on your Mac when you open the lid, and may be accidentally triggered during disassembly. Use this guide to disable Auto Boot.
  • If your MacBook is running Big Sur v11.1 or later, disabling Auto Boot may not work. You can proceed normally, but make sure to disconnect the battery as soon as you’re inside.
  • Completely power off and unplug your MacBook Air before you start. Close the display and flip the entire laptop upside-down.
  • Use a P5 driver to remove the following screws:
  • Two 7.9 mm screws
  • Two 7.1 mm screws
  • Six 2.6 mm screws

Before starting this procedure, you should disable your Mac’s Auto Boot feature. Auto Boot powers on your Mac when you open the lid, and may be accidentally triggered during disassembly. Use this guide to disable Auto Boot.

If your MacBook is running Big Sur v11.1 or later, disabling Auto Boot may not work. You can proceed normally, but make sure to disconnect the battery as soon as you’re inside.

Completely power off and unplug your MacBook Air before you start. Close the display and flip the entire laptop upside-down.

Use a P5 driver to remove the following screws:

Two 7.9 mm screws

Two 7.1 mm screws

Six 2.6 mm screws

1024

Step 2

              Remove the lower case
  • Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
  • Remove the lower case.

Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

Remove the lower case.

Step 3

              Disconnect the battery
  • Peel back the tape covering the battery connector enough to reveal the connector underneath.

Peel back the tape covering the battery connector enough to reveal the connector underneath.

Step 4

  • Use a spudger to slide the battery connector parallel to the logic board and out of its socket on the logic board.

Use a spudger to slide the battery connector parallel to the logic board and out of its socket on the logic board.

Step 5

              Disconnect the antenna bar
  • Use a T3 Torx driver to remove the two 1.4 mm screws securing the antenna cable bracket.
  • Remove the antenna cable bracket.

Use a T3 Torx driver to remove the two 1.4 mm screws securing the antenna cable bracket.

Remove the antenna cable bracket.

Step 6

  • Insert the point of a spudger under one of the antenna cables close to the connector.
  • Pry straight up to disconnect the cable.
  • Repeat for the other antenna cable.

Insert the point of a spudger under one of the antenna cables close to the connector.

Pry straight up to disconnect the cable.

Repeat for the other antenna cable.

Step 7

  • Use a T3 Torx driver to remove the two 1.5 mm screws securing the display cable connector bracket.
  • Remove the display cable connector bracket.

Use a T3 Torx driver to remove the two 1.5 mm screws securing the display cable connector bracket.

Remove the display cable connector bracket.

Step 8

  • Use the flat end of a spudger to pry up the display cable connector.

Use the flat end of a spudger to pry up the display cable connector.

Step 9

  • Use a T5 Torx driver to remove the following screws:
  • Four 7.4 mm screws
  • Two 4.5 mm screws

Use a T5 Torx driver to remove the following screws:

Four 7.4 mm screws

Two 4.5 mm screws

Step 10

              Remove the antenna bar
  • Lift the antenna bar straight up and out of the case. Take care not to snag the antenna bar on any cables or connectors.
  • You may encounter resistance from the clips in the middle of the antenna bar holding it in the case. You may pull hard without damaging anything as long as you pull straight up, perpendicular to the case.
  • Remove the antenna bar.

Lift the antenna bar straight up and out of the case. Take care not to snag the antenna bar on any cables or connectors.

You may encounter resistance from the clips in the middle of the antenna bar holding it in the case. You may pull hard without damaging anything as long as you pull straight up, perpendicular to the case.

Remove the antenna bar.

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Adam O'Camb

Member since: 04/11/2015

173,479 Reputation

                                      418 Guides authored                  



                       Badges:
                       39







                                                        +36 more badges