Macbook Air 13 Mid 2013 Trackpad Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          30 minutes - 2 hours

Sections

Lower Case
2 steps
Battery
3 steps
Trackpad
6 steps

Flags

BackMacBook Air 13" Mid 2013
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Lower Case

Before proceeding, power down your MacBook. Close the display and lay it on a soft surface, top-side down.
Use a P5 Pentalobe driver to remove ten screws securing the lower case, of the following lengths:
Two 9 mm screws
Eight 2.6 mm screws

Before proceeding, power down your MacBook. Close the display and lay it on a soft surface, top-side down.

Use a P5 Pentalobe driver to remove ten screws securing the lower case, of the following lengths:

Two 9 mm screws

Eight 2.6 mm screws

1024

Step 2

Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
Remove the lower case and set it aside.

Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

Remove the lower case and set it aside.

Step 3

              Battery

Grab the clear plastic pull tab attached to the battery connector and pull it toward the front edge of the Air to disconnect the battery from the logic board.
Do not lift upward on the connector as you disconnect it.

Grab the clear plastic pull tab attached to the battery connector and pull it toward the front edge of the Air to disconnect the battery from the logic board.

Do not lift upward on the connector as you disconnect it.

Step 4

Remove the following five screws securing the battery to the upper case:
Three 6.3 mm T5 Torx screws
Two 2.4 mm T5 Torx screws

Remove the following five screws securing the battery to the upper case:

Three 6.3 mm T5 Torx screws

Two 2.4 mm T5 Torx screws

Step 5

When handling the battery, avoid squeezing or touching the four exposed lithium polymer cells.
Lift the battery from its edge nearest the logic board and remove it from the upper case.
If you’re installing a new battery, you should calibrate it after installation:
Charge it to 100%, and then keep charging it for at least 2 more hours. Then, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.
If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook’s SMC.

When handling the battery, avoid squeezing or touching the four exposed lithium polymer cells.

Lift the battery from its edge nearest the logic board and remove it from the upper case.

If you’re installing a new battery, you should calibrate it after installation:

Charge it to 100%, and then keep charging it for at least 2 more hours. Then, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.

If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook’s SMC.

Step 6

              Trackpad

Use the tip of a spudger or your fingernail to flip up the retaining flap on the trackpad ribbon cable ZIF socket.
Be sure you are prying up on the hinged retaining flap, not the socket itself.
Pull the trackpad ribbon cable straight out of its socket toward the rear edge of the Air.

Use the tip of a spudger or your fingernail to flip up the retaining flap on the trackpad ribbon cable ZIF socket.

Be sure you are prying up on the hinged retaining flap, not the socket itself.

Pull the trackpad ribbon cable straight out of its socket toward the rear edge of the Air.

Step 7

While carefully lifting the keyboard ribbon cable with one hand, use the tip of a spudger or your fingernail to flip up the retaining flap on the keyboard ribbon cable ZIF socket.
Be sure you are prying up on the hinged retaining flap, not the socket itself.
Pull the keyboard ribbon cable straight out of its socket toward the front edge of the Air.

While carefully lifting the keyboard ribbon cable with one hand, use the tip of a spudger or your fingernail to flip up the retaining flap on the keyboard ribbon cable ZIF socket.

Pull the keyboard ribbon cable straight out of its socket toward the front edge of the Air.

Step 8

Remove the following twelve screws:
Six 1.6 mm Phillips screws securing the trackpad to the upper case.
Six 1.6 mm Phillips screws securing the trackpad brackets to the trackpad.

Remove the following twelve screws:

Six 1.6 mm Phillips screws securing the trackpad to the upper case.

Six 1.6 mm Phillips screws securing the trackpad brackets to the trackpad.

Step 9

Remove the right and left trackpad brackets from the upper case.

Remove the right and left trackpad brackets from the upper case.

Step 10

During reassembly, check the clicking action on the trackpad.
The 1.4 mm T5 Torx screw near the front edge of the case must be adjusted correctly.
If overtightened, the button will cease to click at a certain point. Adjust the set screw until the clicking side of the trackpad has minimal play.
It’s not necessary to remove this screw in order to remove the trackpad.

During reassembly, check the clicking action on the trackpad.

The 1.4 mm T5 Torx screw near the front edge of the case must be adjusted correctly.

If overtightened, the button will cease to click at a certain point. Adjust the set screw until the clicking side of the trackpad has minimal play.

It’s not necessary to remove this screw in order to remove the trackpad.

Step 11

Use the flat end of a spudger to carefully lift the edge of the trackpad closest to the keyboard from its recess in the upper case by lifting it away from the brackets attached to the upper case.
Remove the trackpad from the upper case.

Use the flat end of a spudger to carefully lift the edge of the trackpad closest to the keyboard from its recess in the upper case by lifting it away from the brackets attached to the upper case.

Remove the trackpad from the upper case.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      31 other people completed this guide.

Author

                                      with 10 other contributors

                    Walter Galan

682,038 Reputation

                                      1,203 Guides authored                  



                       Badges:
                       54







                                                        +51 more badges

ahaffke - Jun 13, 2015

Great write up. Where can I find the keyboard ribbon cable? (the wide one that doesn’t make any 90s. I tore mine with metal tweezers. Can’t find the wide cable anywhere.

emaginechild - Jul 4, 2016

shhhhh, it’s called ie bAe eYe

Scott Salling - Mar 19, 2017

even a 65 year old can do it! (with magnifying glasses) Thank! Fixed the dirty, sticking trackpad!

Marc Malkwitz - Oct 18, 2017

Step 10 should not be done! This is a pure adjustment screw for the clickpoint. Only readjust there, in case clicking does not feel okay after a change of the trackpad. Usually no adjusment is necessary. The trackpad comes out easily after Step 8

Schritt 10 ist falsch! Diese Schraube dient lediglich der Justage des Druckpunkts des Klicks. Sie muss nur verstellt werden, falls der Klick nach dem Wechsel des Trackpads nicht mehr ok ist. Das Trackpad lässt sich aber bereits nach Schritt 8 problemlos entnehmen.

Martijn Verhoeven - Apr 2, 2021

I have replaced the trackpad but it now gives erratic behavior. Usually after booting/opening the lid it works fine for a couple of minutes. Then it stops moving or jumps around the screen after a freeze. Reset SMC does not help unfortunately. Anybody any ideas?

Introduction#

What you need#

Introduction

What you need