Difficulty

Moderate

Steps

7

Time Required

Suggest a time??

Sections

3

  • Lower Case
  • 2 steps
  • Battery
  • 3 steps
  • Left Speaker
  • 2 steps

Flags

0

  • BackMacBook Air 13" Mid 2013

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Lower Case               
  • Before proceeding, power down your MacBook. Close the display and lay it on a soft surface, top-side down.
  • Use a P5 Pentalobe driver to remove ten screws securing the lower case, of the following lengths:
  • Two 9 mm screws
  • Eight 2.6 mm screws

Before proceeding, power down your MacBook. Close the display and lay it on a soft surface, top-side down.

Use a P5 Pentalobe driver to remove ten screws securing the lower case, of the following lengths:

Two 9 mm screws

Eight 2.6 mm screws

1024

Step 2

  • Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
  • Remove the lower case and set it aside.

Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

Remove the lower case and set it aside.

Step 3

              Battery               
  • Grab the clear plastic pull tab attached to the battery connector and pull it toward the front edge of the Air to disconnect the battery from the logic board.
  • Do not lift upward on the connector as you disconnect it.

Grab the clear plastic pull tab attached to the battery connector and pull it toward the front edge of the Air to disconnect the battery from the logic board.

Do not lift upward on the connector as you disconnect it.

Step 4

  • Remove the following five screws securing the battery to the upper case:
  • Three 6.3 mm T5 Torx screws
  • Two 2.4 mm T5 Torx screws

Remove the following five screws securing the battery to the upper case:

Three 6.3 mm T5 Torx screws

Two 2.4 mm T5 Torx screws

Step 5

  • When handling the battery, avoid squeezing or touching the four exposed lithium polymer cells.
  • Lift the battery from its edge nearest the logic board and remove it from the upper case.
  • If you’re installing a new battery, you should calibrate it after installation:
  • Charge it to 100%, and then keep charging it for at least 2 more hours. Then, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.
  • If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook’s SMC.

When handling the battery, avoid squeezing or touching the four exposed lithium polymer cells.

Lift the battery from its edge nearest the logic board and remove it from the upper case.

If you’re installing a new battery, you should calibrate it after installation:

Charge it to 100%, and then keep charging it for at least 2 more hours. Then, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.

If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook’s SMC.

Step 6

              Left Speaker               
  • Use the flat end of a spudger to pry the left speaker cable connector up and out of its socket on the I/O board.
  • Pry up from beneath the wires.

Use the flat end of a spudger to pry the left speaker cable connector up and out of its socket on the I/O board.

Pry up from beneath the wires.

Step 7

  • Use the flat end of a spudger to pry the left speaker off the adhesive securing it to the upper case.
  • Remove the left speaker from the upper case.

Use the flat end of a spudger to pry the left speaker off the adhesive securing it to the upper case.

Remove the left speaker from the upper case.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      4 other people completed this guide.                                             

Author

                                      with 4 other contributors 

                    Walter Galan                     

682,038 Reputation

                                      1,203 Guides authored                  



                       Badges:
                       54







                                                        +51 more badges