Difficulty

Moderate

Steps

6

Time Required

                          15 minutes

Sections

3

  • Lower Case
  • 2 steps
  • Battery Connector
  • 1 step
  • I/O Board Cable
  • 3 steps

Flags

0

  • BackMacBook Air 13" Mid 2013

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Lower Case
  • Before proceeding, power down your MacBook. Close the display and lay it on a soft surface, top-side down.
  • Use a P5 Pentalobe driver to remove ten screws securing the lower case, of the following lengths:
  • Two 9 mm screws
  • Eight 2.6 mm screws

Before proceeding, power down your MacBook. Close the display and lay it on a soft surface, top-side down.

Use a P5 Pentalobe driver to remove ten screws securing the lower case, of the following lengths:

Two 9 mm screws

Eight 2.6 mm screws

1024

Step 2

  • Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
  • Remove the lower case and set it aside.

Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

Remove the lower case and set it aside.

Step 3

              Battery Connector
  • To ensure that everything is de-energized and won’t turn on while you’re working, it is recommended that you disconnect the battery.
  • Grab the clear plastic pull tab attached to the battery connector and pull it parallel to the board toward the front edge of the Air.
  • Do not lift upward on the connector as you disconnect it or you risk damage to the connector socket.

To ensure that everything is de-energized and won’t turn on while you’re working, it is recommended that you disconnect the battery.

Grab the clear plastic pull tab attached to the battery connector and pull it parallel to the board toward the front edge of the Air.

Do not lift upward on the connector as you disconnect it or you risk damage to the connector socket.

Step 4

              I/O Board Cable
  • Use the flat end of a spudger to pry the I/O board cable connector up out of its socket on the I/O board.

Use the flat end of a spudger to pry the I/O board cable connector up out of its socket on the I/O board.

Step 5

  • Carefully peel the I/O board cable from the adhesive securing it to the top of the fan.
  • During reassembly, make sure this cable is in the correct orientation. It will fit if reversed, but the laptop will not boot.

Carefully peel the I/O board cable from the adhesive securing it to the top of the fan.

During reassembly, make sure this cable is in the correct orientation. It will fit if reversed, but the laptop will not boot.

Step 6

  • The following connector has an especially deep socket. Use care when disconnecting it.
  • While gently pulling the I/O board cable upward near its connection to the logic board, use the flat end of a spudger to pry up on alternating sides of the connector to help “walk” it out of its socket.
  • Remove the I/O board cable.

The following connector has an especially deep socket. Use care when disconnecting it.

While gently pulling the I/O board cable upward near its connection to the logic board, use the flat end of a spudger to pry up on alternating sides of the connector to help “walk” it out of its socket.

Remove the I/O board cable.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.

Author

                                      with 7 other contributors 


                    Walter Galan

682,038 Reputation

                                      1,203 Guides authored                  



                       Badges:
                       54







                                                        +51 more badges