Difficulty
Moderate
Steps
8
Time Required
10 - 30 minutes
Sections
3
- Lower Case
- 2 steps
- Battery Disconnection
- 1 step
- USB-C Board
- 5 steps
Flags
0
BackMacBook Air 13" Retina Late 2020
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Remove the screws securing the lower case
- Before starting this procedure, you should disable your Mac’s Auto Boot feature. Auto Boot powers on your Mac when you open the lid, and may be accidentally triggered during disassembly. Use this guide to disable Auto Boot.
- If your MacBook is running Big Sur v11.1 or later, disabling Auto Boot may not work. You can proceed normally, but make sure to disconnect the battery as soon as you’re inside.
- Completely power off and unplug your MacBook before you start. Close the display and flip the entire laptop upside-down.
- Use a P5 driver to remove the following screws:
- Two 7.9 mm screws
- Two 7.3 mm screws
- Six 2.6 mm screws
- Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your MacBook.
Before starting this procedure, you should disable your Mac’s Auto Boot feature. Auto Boot powers on your Mac when you open the lid, and may be accidentally triggered during disassembly. Use this guide to disable Auto Boot.
If your MacBook is running Big Sur v11.1 or later, disabling Auto Boot may not work. You can proceed normally, but make sure to disconnect the battery as soon as you’re inside.
Completely power off and unplug your MacBook before you start. Close the display and flip the entire laptop upside-down.
Use a P5 driver to remove the following screws:
Two 7.9 mm screws
Two 7.3 mm screws
Six 2.6 mm screws
Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your MacBook.
1024
Step 2
Remove the lower case
- Wedge your fingers between the display and the lower case and pull upward to pop off the lower case.
- Remove the lower case.
- To reinstall the lower case:
- Set it in place and press firmly to engage the two hidden clips underneath. You should feel and hear them snap into place.
Wedge your fingers between the display and the lower case and pull upward to pop off the lower case.
Remove the lower case.
To reinstall the lower case:
Set it in place and press firmly to engage the two hidden clips underneath. You should feel and hear them snap into place.
Step 3
Disconnect the battery
- Use the flat end of a spudger to pry up and unlatch the metal locking arm on the battery connector.
- Make sure the metal arm is completely free of the locking tab before lifting the battery connector. The metal locking arm should easily unlatch.
- Lift straight up on the metal locking arm to pull the battery connector out of its socket on the logic board.
- During reassembly, press the battery connector straight down into its socket, making sure it sits flush within the socket.
Use the flat end of a spudger to pry up and unlatch the metal locking arm on the battery connector.
Make sure the metal arm is completely free of the locking tab before lifting the battery connector. The metal locking arm should easily unlatch.
Lift straight up on the metal locking arm to pull the battery connector out of its socket on the logic board.
During reassembly, press the battery connector straight down into its socket, making sure it sits flush within the socket.
Step 4
Disconnect the USB-C board
- Use a T3 Torx driver to remove the two 1.4 mm screws securing the USB-C connector cover.
- If your T3 bit feels a bit too loose, you may need to use a T4.
Use a T3 Torx driver to remove the two 1.4 mm screws securing the USB-C connector cover.
If your T3 bit feels a bit too loose, you may need to use a T4.
Step 5
- Remove the USB-C connector cover.
Remove the USB-C connector cover.
Step 6
- Use the flat end of a spudger to pry the USB-C cable connector up and out of its socket on the logic board.
Use the flat end of a spudger to pry the USB-C cable connector up and out of its socket on the logic board.
Step 7
Remove the USB-C board
- Use a T5 Torx driver to remove the two 2.9 mm screws securing the USB-C board.
Use a T5 Torx driver to remove the two 2.9 mm screws securing the USB-C board.
Step 8
- Use a pair of tweezers to remove the USB-C board.
Use a pair of tweezers to remove the USB-C board.
Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.
To reassemble your device, follow the above steps in reverse order.
Take your e-waste to an R2 or e-Stewards certified recycler.
Repair didn’t go as planned? Check out our Answers community for troubleshooting help.
Cancel: I did not complete this guide.
10 other people completed this guide.
Author
Carsten Frauenheim
Member since: 03/10/2020
81,713 Reputation
330 Guides authored
Badges:
38
+35 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,772 Guides authored
Zachary Barber - Sep 20, 2022
Reply
This guide was excellent. Easy & painless, even though it was the most complex repair I’ve taken on myself. Thanks for saving time & money.
Gurmeet Sahotay - Oct 22, 2022
Reply
Do you sell the screws for the usb c board? I have lost one of the 1.4mm torx screws which hold down the connector of the usb board.
Michael C Crotty - Nov 15, 2022
Reply
This was quite easy, thanks so much Carsten!
Resana Laucast - Dec 20, 2022
Reply
where can I get the part for my computer MacBook Air M1 2020 Usb-C connector model A2337 EMC 3598 serial CO2FN1R2Q6LC.
Where can I buy it online….
Alex Firth - Dec 23, 2022
If you’re in selected countries in Europe or the USA, you can now order this part from Apple directly using their Self Service Repair store :)