Macbook Air 13 Late 2010 Heat Sink Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          25 minutes - 2 hours

Sections

Lower Case
2 steps
Battery
1 step
I/O Board Cable
2 steps
Fan
4 steps
I/O Board
6 steps
Heat Sink
5 steps

Flags

BackMacBook Air 13" Late 2010
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Lower Case

Before proceeding, power off the device, close the lid and lay it on a soft surface top-side down.
Remove the following ten screws:
Two 9 mm 5-point Pentalobe screws
Eight 2.6 mm 5-point Pentalobe screws
The special screwdriver needed to remove the eight 5-point Pentalobe screws can be found here.

Before proceeding, power off the device, close the lid and lay it on a soft surface top-side down.

Remove the following ten screws:

Two 9 mm 5-point Pentalobe screws

Eight 2.6 mm 5-point Pentalobe screws

The special screwdriver needed to remove the eight 5-point Pentalobe screws can be found here.

1024

Step 2

Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
Remove the lower case and set it aside.

Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

Remove the lower case and set it aside.

Step 3

              Battery

For precautionary purposes, we advise that you disconnect the battery connector from the logic board to avoid any electrical discharge. This step is optional and is not required.
Grab the clear plastic pull tab attached to the battery connector and pull it toward the front edge of the Air to disconnect the battery from the logic board.
Do not lift upward on the connector as you disconnect it.

For precautionary purposes, we advise that you disconnect the battery connector from the logic board to avoid any electrical discharge. This step is optional and is not required.

Grab the clear plastic pull tab attached to the battery connector and pull it toward the front edge of the Air to disconnect the battery from the logic board.

Do not lift upward on the connector as you disconnect it.

Step 4

              I/O Board Cable

Use the flat end of a spudger to pry the I/O board cable connector upward out of its socket on the I/O board.

Use the flat end of a spudger to pry the I/O board cable connector upward out of its socket on the I/O board.

Step 5

The following connector has an especially deep socket. Use care when disconnecting it.
Carefully peel the I/O board cable from the top of the fan.
While gently pulling the I/O board cable upward near its connection to the logic board, use the tip of a spudger to pry upward on alternating sides of the connector to help “walk” it out of its socket.
Remove the I/O board cable.

The following connector has an especially deep socket. Use care when disconnecting it.

Carefully peel the I/O board cable from the top of the fan.

While gently pulling the I/O board cable upward near its connection to the logic board, use the tip of a spudger to pry upward on alternating sides of the connector to help “walk” it out of its socket.

Remove the I/O board cable.

Step 6

Fan

Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.
Be sure you are prying up on the hinged retaining flap, not the socket itself.

Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.

Be sure you are prying up on the hinged retaining flap, not the socket itself.

Step 7

Peel the rubber gasket off the adhesive on the top of the fan.

Peel the rubber gasket off the adhesive on the top of the fan.

Step 8

Remove the following three screws securing the fan to the upper case:
One 3.6 mm T5 Torx screw
One 2.7 mm T5 Torx screw
One 3.6 mm T5 Torx screw with a short head

Remove the following three screws securing the fan to the upper case:

One 3.6 mm T5 Torx screw

One 2.7 mm T5 Torx screw

One 3.6 mm T5 Torx screw with a short head

Step 9

Lift the fan out of the upper case and carefully pull the fan ribbon cable out of its socket as you remove it from the Air.

Lift the fan out of the upper case and carefully pull the fan ribbon cable out of its socket as you remove it from the Air.

Step 10

              I/O Board

Disconnect the I/O board by pulling the power cable away from its socket on the logic board.
Pull the cable parallel to the face of the logic board toward the right edge of the Air.

Disconnect the I/O board by pulling the power cable away from its socket on the logic board.

Pull the cable parallel to the face of the logic board toward the right edge of the Air.

Step 11

Pull the camera cable parallel to the face of the I/O board toward the corner of the Air to disconnect it from its socket, using the tip of a spudger to help push the connector out of its socket.
Do not lift upward on this cable as you disconnect it, as its socket may break off the logic board.

Pull the camera cable parallel to the face of the I/O board toward the corner of the Air to disconnect it from its socket, using the tip of a spudger to help push the connector out of its socket.

Do not lift upward on this cable as you disconnect it, as its socket may break off the logic board.

Step 12

Use the flat end of a spudger to pry the left speaker cable connector up and out of its socket on the I/O board.
Pry up from beneath the wires.
De-route the left speaker cable from its retainer on the I/O board.

Use the flat end of a spudger to pry the left speaker cable connector up and out of its socket on the I/O board.

Pry up from beneath the wires.

De-route the left speaker cable from its retainer on the I/O board.

Step 13

Use the flat end of a spudger to pry the microphone cable connector up and out of its socket on the I/O board.
Pry up from beneath the wires.

Use the flat end of a spudger to pry the microphone cable connector up and out of its socket on the I/O board.

Step 14

Remove the single 3.6 mm T5 Torx screw securing the I/O board to the upper case.

Remove the single 3.6 mm T5 Torx screw securing the I/O board to the upper case.

Step 15

Carefully lift the I/O board from its edge nearest the logic board and remove it from the upper case.

Carefully lift the I/O board from its edge nearest the logic board and remove it from the upper case.

Step 16

              Heat Sink

Remove the eight 2.5 mm T5 Torx screws securing the heat sink to the logic board.

Remove the eight 2.5 mm T5 Torx screws securing the heat sink to the logic board.

Step 17

Remove the two 4.9 mm T8 Torx screw securing the antenna cable retainer on the left display hinge to the upper case.

Remove the two 4.9 mm T8 Torx screw securing the antenna cable retainer on the left display hinge to the upper case.

Step 18

Push the antenna cable retainer out of the way and remove the 3 mm T5 Torx screw securing the end of the heat sink to the upper case.

Push the antenna cable retainer out of the way and remove the 3 mm T5 Torx screw securing the end of the heat sink to the upper case.

Step 19

If the heat sink seems to be stuck to the logic board after removing all eight screws, use a spudger to carefully separate the heat sink from the faces of the CPU and GPU.
Remove the heat sink from the logic board.
When reinstalling the heat sink, be sure to apply a new layer of thermal paste. If you have never applied thermal paste before, we have a guide that makes it easy.

If the heat sink seems to be stuck to the logic board after removing all eight screws, use a spudger to carefully separate the heat sink from the faces of the CPU and GPU.

Remove the heat sink from the logic board.

When reinstalling the heat sink, be sure to apply a new layer of thermal paste. If you have never applied thermal paste before, we have a guide that makes it easy.

Step 20

These shots show how the rubber fan gasket should be installed during reassembly. Be sure not to install the gasket underneath the ear where the end of the heatsink is screwed down to the upper case.
Additionally, be sure the small post molded into the rubber gasket mates with the hole cut into the upper right corner of the logic board.

These shots show how the rubber fan gasket should be installed during reassembly. Be sure not to install the gasket underneath the ear where the end of the heatsink is screwed down to the upper case.

Additionally, be sure the small post molded into the rubber gasket mates with the hole cut into the upper right corner of the logic board.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.

Author

                                      with 4 other contributors

                    Andrew Bookholt

575,478 Reputation

                                      618 Guides authored                  



                       Badges:
                       47







                                                        +44 more badges

Introduction#

What you need#

Introduction

What you need