Macbook Air 11 Mid 2013 Trackpad Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          15 - 30 minutes

Sections

Lower Case
2 steps
Battery Connector
1 step
Battery
2 steps
Trackpad
4 steps

Flags

BackMacBook Air 11" Mid 2013
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Lower Case

Shut down and close your computer. Lay it on a soft surface top-side down.
Remove the following ten screws:
Two 8 mm 5-point Pentalobe screws
Eight 2.5 mm 5-point Pentalobe screws
The special screwdriver needed to remove the 5-point Pentalobe screws can be found here.

Shut down and close your computer. Lay it on a soft surface top-side down.

Remove the following ten screws:

Two 8 mm 5-point Pentalobe screws

Eight 2.5 mm 5-point Pentalobe screws

The special screwdriver needed to remove the 5-point Pentalobe screws can be found here.

1024

Step 2

Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

Step 3

              Battery Connector

In this step you will disconnect the battery to help avoid shorting out any components during service.
Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.
Bend the battery cable slightly away from the logic board so the connector will not accidentally bend back and make contact with its socket.

In this step you will disconnect the battery to help avoid shorting out any components during service.

Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.

Bend the battery cable slightly away from the logic board so the connector will not accidentally bend back and make contact with its socket.

Step 4

              Battery

Remove the following five screws securing the battery to the upper case:
Two 5.2 mm T5 Torx screws
One 6 mm T5 Torx screw
Two 2.6 mm T5 Torx screws

Remove the following five screws securing the battery to the upper case:

Two 5.2 mm T5 Torx screws

One 6 mm T5 Torx screw

Two 2.6 mm T5 Torx screws

Step 5

When handling the battery, avoid squeezing or touching the six exposed lithium polymer cells.
Lift the battery from its edge nearest the logic board and remove it from the upper case.
If you’re installing a new battery, you should calibrate it after installation:
Charge it to 100%, and then keep charging it for at least 2 more hours. Next, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.
If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook’s SMC.

When handling the battery, avoid squeezing or touching the six exposed lithium polymer cells.

Lift the battery from its edge nearest the logic board and remove it from the upper case.

If you’re installing a new battery, you should calibrate it after installation:

Charge it to 100%, and then keep charging it for at least 2 more hours. Next, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.

If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook’s SMC.

Step 6

              Trackpad

Use the point of a spudger to lift the ZIF connector retaining flap on the trackpad data cable.
Gently slide the ribbon cable out of the ZIF connector.
Adjust, but do not remove the T5 Trackpad Sensitivity Screw to change the trackpad’s depth sensitivity.

Use the point of a spudger to lift the ZIF connector retaining flap on the trackpad data cable.

Gently slide the ribbon cable out of the ZIF connector.

Adjust, but do not remove the T5 Trackpad Sensitivity Screw to change the trackpad’s depth sensitivity.

Step 7

With one hand, push the keyboard ribbon cable in slightly to access the ZIF connector beneath it.
Use a spudger to flip up the retaining flap.
Gently slide the cable out of the connector.

With one hand, push the keyboard ribbon cable in slightly to access the ZIF connector beneath it.

Use a spudger to flip up the retaining flap.

Gently slide the cable out of the connector.

Step 8

Remove the six 1.5 mm Phillips #00 screws holding the trackpad in place.
These screws are installed tightly and strip easily. Be careful as you remove them.

Remove the six 1.5 mm Phillips #00 screws holding the trackpad in place.

These screws are installed tightly and strip easily. Be careful as you remove them.

Step 9

Open the device about 10 degrees.
While holding the bottom of the trackpad, press up on the side of the trackpad closest to the logic board to free it from the upper case.
Remove the trackpad from the device.

Open the device about 10 degrees.

While holding the bottom of the trackpad, press up on the side of the trackpad closest to the logic board to free it from the upper case.

Remove the trackpad from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      15 other people completed this guide.

Author

                                      with 6 other contributors

                    Sam Goldheart

Member since: 10/18/2012

455,549 Reputation

                                      548 Guides authored                  



                       Badges:
                       48







                                                        +45 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,767 Guides authored

andresaldana - Nov 21, 2016

Followed the instructions in order to adjust the sensitivity of the trackpad, nonetheless the screw I found was a T6, not a T5. But in any case, excellent guide, thank you!

Lane Jasper - Feb 22, 2018

any chance this part is the same for a mid 2012 11” ?

Sam Goldheart - Feb 23, 2018

If you click the part at the top of the guide, you can see the compatibility listed, unfortunately they’re not the same, but we do have the 11” trackpad here. And the accompanying guide lives here!

Introduction#

What you need#

Team#

Introduction

What you need

Team