Difficulty

Moderate

Steps

5

Time Required

                          5 - 10 minutes

Sections

3

  • Lower Case
  • 2 steps
  • Battery Connector
  • 1 step
  • SSD
  • 2 steps

Flags

0

  • BackMacBook Air 11" Mid 2013

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Before you perform this repair, if at all possible, back up your existing SSD. Then, either familiarize yourself with internet recovery or create a bootable external drive so you’ll be ready to install macOS onto your new drive and migrate your data to the new SSD.

Finally, we strongly recommend installing macOS 10.13 High Sierra (or a later macOS) before replacing the original SSD from your MacBook Air. Most new SSDs require updated storage drivers not found in versions of macOS prior to High Sierra.

What you need

Step 1

              Lower Case
  • Shut down and close your computer. Lay it on a soft surface top-side down.
  • Remove the following ten screws:
  • Two 8 mm 5-point Pentalobe screws
  • Eight 2.5 mm 5-point Pentalobe screws
  • The special screwdriver needed to remove the 5-point Pentalobe screws can be found here.

Shut down and close your computer. Lay it on a soft surface top-side down.

Remove the following ten screws:

Two 8 mm 5-point Pentalobe screws

Eight 2.5 mm 5-point Pentalobe screws

The special screwdriver needed to remove the 5-point Pentalobe screws can be found here.

1024

Step 2

  • Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

Step 3

              Battery Connector
  • In this step you will disconnect the battery to help avoid shorting out any components during service.
  • Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.
  • Bend the battery cable slightly away from the logic board so the connector will not accidentally bend back and make contact with its socket.

In this step you will disconnect the battery to help avoid shorting out any components during service.

Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.

Bend the battery cable slightly away from the logic board so the connector will not accidentally bend back and make contact with its socket.

Step 4

              SSD
  • Remove the single 2.9 mm T5 Torx screw securing the SSD to the logic board.

Remove the single 2.9 mm T5 Torx screw securing the SSD to the logic board.

Step 5

  • Lift the free end of the SSD just enough to get a good hold of it.
  • Do not excessively lift the end of the SSD.
  • Pull the drive straight out of its socket and remove it from the logic board.
  • When reinstalling the SSD, be sure it is properly seated before reinstalling its retaining screw.

Lift the free end of the SSD just enough to get a good hold of it.

Do not excessively lift the end of the SSD.

Pull the drive straight out of its socket and remove it from the logic board.

When reinstalling the SSD, be sure it is properly seated before reinstalling its retaining screw.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      50 other people completed this guide.

Author

                                      with 6 other contributors 


                    Sam Goldheart

Member since: 10/18/2012

455,549 Reputation

                                      548 Guides authored                  



                       Badges:
                       48







                                                        +45 more badges

Team

                       iFixit                        

                                                  Member of iFixit 



                    Community                     


                                            141 Members                     


                                            15,767 Guides authored

Roland - Feb 2, 2015

Reply

Is it possible to replace a 128 GB SSD with a 256 GB SSD without any problems?

Felipe - Nov 23, 2015

Reply

Anyone knows if you can replace the msata ssd or if it is proprietary of apple?

brendanorourke - Jan 8, 2016

Reply

I wonder if someone can help me - I completed the installation and rebooted from a clone of the original drive on an external USB disk. I tried to clone that back onto the new SSD but that failed and now the new SSD does not appear on the desktop and does not appear in Disk Utility. Its not being recognised when I boot up. Do you have any ideas how I can get it to reappear - I assume the format is lost so is there a way to reformat?

mohd.a2017 - Jan 24, 2017

Reply

Can i upgrade my ssd drive from 128 to 1TB ?

pulido_066 - Jun 7, 2019

i want to know too