Difficulty
Moderate
Steps
10
Time Required
Suggest a time??
Sections
4
- Lower Case
- 2 steps
- Battery Connector
- 1 step
- Battery
- 2 steps
- Left Speaker
- 5 steps
Flags
0
BackMacBook Air 11" Mid 2013
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Lower Case
- Shut down and close your computer. Lay it on a soft surface top-side down.
- Remove the following ten screws:
- Two 8 mm 5-point Pentalobe screws
- Eight 2.5 mm 5-point Pentalobe screws
- The special screwdriver needed to remove the 5-point Pentalobe screws can be found here.
Shut down and close your computer. Lay it on a soft surface top-side down.
Remove the following ten screws:
Two 8 mm 5-point Pentalobe screws
Eight 2.5 mm 5-point Pentalobe screws
The special screwdriver needed to remove the 5-point Pentalobe screws can be found here.
1024
Step 2
- Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
Step 3
Battery Connector
- In this step you will disconnect the battery to help avoid shorting out any components during service.
- Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.
- Bend the battery cable slightly away from the logic board so the connector will not accidentally bend back and make contact with its socket.
In this step you will disconnect the battery to help avoid shorting out any components during service.
Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.
Bend the battery cable slightly away from the logic board so the connector will not accidentally bend back and make contact with its socket.
Step 4
Battery
- Remove the following five screws securing the battery to the upper case:
- Two 5.2 mm T5 Torx screws
- One 6 mm T5 Torx screw
- Two 2.6 mm T5 Torx screws
Remove the following five screws securing the battery to the upper case:
Two 5.2 mm T5 Torx screws
One 6 mm T5 Torx screw
Two 2.6 mm T5 Torx screws
Step 5
- When handling the battery, avoid squeezing or touching the six exposed lithium polymer cells.
- Lift the battery from its edge nearest the logic board and remove it from the upper case.
- If you’re installing a new battery, you should calibrate it after installation:
- Charge it to 100%, and then keep charging it for at least 2 more hours. Next, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.
- If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook’s SMC.
When handling the battery, avoid squeezing or touching the six exposed lithium polymer cells.
Lift the battery from its edge nearest the logic board and remove it from the upper case.
If you’re installing a new battery, you should calibrate it after installation:
Charge it to 100%, and then keep charging it for at least 2 more hours. Next, unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.
If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook’s SMC.
Step 6
Left Speaker
- Use the flat end of a spudger to pry the I/O board cable connector up off its socket on the I/O board.
- Bend the cable away from the I/O board.
Use the flat end of a spudger to pry the I/O board cable connector up off its socket on the I/O board.
Bend the cable away from the I/O board.
Step 7
- Use the tip of a spudger to de-route the left speaker cable from the notch cut into the edge of the I/O board.
Use the tip of a spudger to de-route the left speaker cable from the notch cut into the edge of the I/O board.
Step 8
- Use the flat end of a spudger to pry the left speaker connector up and out of its socket on the I/O board.
- Make sure to pry upward from beneath the wires.
Use the flat end of a spudger to pry the left speaker connector up and out of its socket on the I/O board.
Make sure to pry upward from beneath the wires.
Step 9
- Use the flat end of a spudger to pry the left speaker off the adhesive securing it to the upper case.
- Only pry up on the speaker from the areas of bare aluminum on the upper case. Prying up from the keyboard area may damage the keyboard and the speaker itself.
Use the flat end of a spudger to pry the left speaker off the adhesive securing it to the upper case.
Only pry up on the speaker from the areas of bare aluminum on the upper case. Prying up from the keyboard area may damage the keyboard and the speaker itself.
Step 10
- Remove the left speaker from the upper case.
Remove the left speaker from the upper case.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 3 other contributors
Sam Goldheart
Member since: 10/18/2012
455,549 Reputation
548 Guides authored
Badges:
48
+45 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,767 Guides authored
