Difficulty
Moderate
Steps
10
Time Required
15 minutes - 1 hour
Sections
4
- Lower Case
- 2 steps
- Battery Connector
- 1 step
- I/O Board Cable
- 2 steps
- Fan
- 5 steps
Flags
0
BackMacBook Air 11" Mid 2013
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Lower Case
- Shut down and close your computer. Lay it on a soft surface top-side down.
- Remove the following ten screws:
- Two 8 mm 5-point Pentalobe screws
- Eight 2.5 mm 5-point Pentalobe screws
- The special screwdriver needed to remove the 5-point Pentalobe screws can be found here.
Shut down and close your computer. Lay it on a soft surface top-side down.
Remove the following ten screws:
Two 8 mm 5-point Pentalobe screws
Eight 2.5 mm 5-point Pentalobe screws
The special screwdriver needed to remove the 5-point Pentalobe screws can be found here.
1024
Step 2
- Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
Step 3
Battery Connector
- In this step you will disconnect the battery to help avoid shorting out any components during service.
- Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.
- Bend the battery cable slightly away from the logic board so the connector will not accidentally bend back and make contact with its socket.
In this step you will disconnect the battery to help avoid shorting out any components during service.
Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.
Bend the battery cable slightly away from the logic board so the connector will not accidentally bend back and make contact with its socket.
Step 4
I/O Board Cable
- Use the flat end of a spudger to pry the left and right I/O board cable connectors up off their respective sockets on the I/O board.
Use the flat end of a spudger to pry the left and right I/O board cable connectors up off their respective sockets on the I/O board.
Step 5
- Lift and remove the I/O board cable.
Lift and remove the I/O board cable.
Step 6
Fan
- Use the tip of a spudger to carefully push on each side of the iSight camera cable connector to loosen it out of its socket on the logic board.
- We recommend you gently “walk” the connector out of its socket.
Use the tip of a spudger to carefully push on each side of the iSight camera cable connector to loosen it out of its socket on the logic board.
We recommend you gently “walk” the connector out of its socket.
Step 7
- Peel the iSight camera cable up off the adhesive securing it to the fan.
Peel the iSight camera cable up off the adhesive securing it to the fan.
Step 8
- Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.
- Be sure you are prying up on the hinged retaining flap, not the socket itself.
Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.
Be sure you are prying up on the hinged retaining flap, not the socket itself.
Step 9
- Remove the following three screws securing the fan to the upper case:
- Two 5.5 mm T5 Torx screws
- One 4.6 mm T5 Torx screw
- In some models this is a 3.6 mm T5 Torx screw.
Remove the following three screws securing the fan to the upper case:
Two 5.5 mm T5 Torx screws
One 4.6 mm T5 Torx screw
In some models this is a 3.6 mm T5 Torx screw.
Step 10
- Lift, but do not remove the fan out of its recess in the upper case.
- Carefully pull the fan ribbon cable out of its socket as you remove the fan from the Air.
Lift, but do not remove the fan out of its recess in the upper case.
Carefully pull the fan ribbon cable out of its socket as you remove the fan from the Air.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
14 other people completed this guide.
Author
with 8 other contributors
Sam Goldheart
Member since: 10/18/2012
455,549 Reputation
548 Guides authored
Badges:
48
+45 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,767 Guides authored
Liviolog4 - Feb 20, 2016
Reply
I have error PPF004.
